Maintenance
X-Series—Block Height and Rake Table
Deck
Size
Front Block
Height “A”
Rear Block
Height “B”
Rake “R”
48,
52, &
60
2.63 inches
(6.7 cm)
2.88 inches
(7.3 cm)
1/16–5/16 inch
(1.6–7.9 mm)
10. Carefully rotate the blades side to side (Figure 65).
11. Loosen the leveling adjust locking nuts (item 1
Figure 67) on all four corners so that the deck is
sitting securely on all four blocks. Make sure that
the slack is removed from the deck hangers and
the deck lift foot lever is pushed back against the
stop, then tighten the four leveling adjust locking
nuts.
Figure 67
1.
Leveling adjust locking
nuts
3.
Deck hanger
2.
Deck lift arm
4.
Chain
12. Recheck that blocks fit just snugly under the deck
skirt. Make sure all attachment bolts are tight
13. Continue leveling the deck by checking the
front-to-rear blade slope; refer to
Adjusting the
Blade Slope.
14. Recheck blades for levelness and repeat deck
leveling procedure if necessary.
15. For 60 Inch Decks Only:
A. Raise the deck to the transport (5 inch (12.7
cm) cutting height) position.
B. Reinstall the lift assist spring adjusting screw
that was removed in step 8.
C. Set the gap between the spring and bracket to
3/4–7/8 inch (19–22 mm).
Adjusting the Blade Slope
1. Check the front-to-rear blade level. If the front
blade tip is not “R” (see Block Height and Rake
Table in
Deck Leveling
) lower than the rear
blade tip, adjust the blade level using the following
instructions:
2. Park the machine on a level surface and disengage
the blade control switch.
3. Move the motion control levers outward to the
neutral position, engage the parking brake, stop
the engine, remove the key, and wait for all
moving parts to stop before leaving the operating
position.
4. Check the air pressure of all four tires. If needed,
adjust to the recommended inflation; refer to
Checking the Tire Pressure
in Drive System
Maintenance section.
5. Check and adjust the side-to-side blade level if
you have not checked the setting; refer to
Deck
Leveling
.
6. Set the height-of-cut lever to the 3 inch (76 mm)
position. Place two “B” thick blocks (see Block
Height and Rake Table in
Deck Leveling
) under
the rear edge of the cutting deck skirt; one on
each side of the cutting deck. Place two “A” thick
blocks (see Block Height and Rake Table in
Deck
Leveling
) under each side of the front edge of the
deck, but not under the anti-scalp roller brackets.
7. Loosen the leveling adjust locking nuts (item 1
Figure 67) on all four corners so that the deck is
sitting securely on all four blocks. Make sure that
the slack is removed from the deck hangers and
the deck lift foot lever is pushed back against the
stop, then tighten the four leveling adjust locking
nuts.
8. Carefully rotate the blades so they are facing front
to rear (Figure 68).
9. For 60 Inch Decks Only:
A. Raise the deck to the transport (5 inch (12.7
cm) cutting height) position.
B. Slowly loosen the adjusting screw on the
lift assist spring until the screw can be
64
Summary of Contents for RADIUS
