12
TRANSPORTATION AND STORAGE
Shaking and crashing of the machine should be prevented when transporting it. Store it in a properly
ventilated area with dry air and without any corrosive gas. Store the device with the polishing disk facing up.
Polishing bonnets should be removed from the disk - the disk is not susceptible to deformation.
CLEANING AND MAINTENANCE
Always unplug the device before cleaning it and after each use. Never spray the device with water jets. To
keep the machine clean, clean it with water mixed with soap using a soft cloth. Do not use brushes or other
cleaning tools that may scratch/damage the machine. Care must be taken in order to prevent water flowing
inside the ventilation slots located on the housing. Ventilation slots should be cleaned using a brush and
compressed air. Polishing bonnets may be hand washed, using a mild detergent (do not wash in a washing
machine).
CHECK REGULARLY THE DEVICE
Check regularly the machine for signs of damage. If the machine is damaged, please stop using it immediately
and contact your customer service to solve the problem.
What to do in case of a problem?
Please contact your customer service and prepare following information:
•
Invoice number and serial number (the latter is to be found on the technical plate on the machine).
•
If relevant, take a picture of the damaged, broken or defective part.
•
It will be easier for your customer service clerk to determine the source of the problem if you give
a detailed and precise description of the matter. Avoid formulations like „the device doesn’t ́t heat up”,
which may mean that it doesn’t ́t heat enough or even not at all. The more detailed your information,
the better customer service will be able to solve your problem rapidly and efficiently!
CAUTION:
Never open the machine without the authorization of your customer service. This can lead
to a loss of warranty!
MSW-POL120C (6234)
1.
ON/OFF switch
2.
handles
3.
polishing disk
1
2
3
MSW-POL60C (6235)
1.
ON/OFF switch
2.
polishing disk
PRINCIPLES OF OPERATION
Before the first use
•
Make sure the power supply voltage matches that on the device rating plate.
•
Before connecting the machine to a power source, make sure the ON/OFF switch is in the OFF
position. If the switch is in the ON position, connecting the machine to a power supply will activate it,
which might cause an accident!
•
Check the state of the power cable and plug. If the power cable needs replacing, seek the services of
a qualified technician.
Switching on and off
To start using the device, press/slide the ON/OFF switch. If using the MSW-POL560C (6233) model, before
starting, set the switch to the slowest speed – then adjust the speed once the device starts.
Do not use the device while standing on a ladder. Both hands have to be free in order to use the device.
If the device is to be operated whilst working at heights, make sure an appropriative, stable platform or
scaffolding with bannisters and security supports is used. Disconnect from power source before commencing
maintenance, lubrication, adjusting and replacing accessories (e.g. polishing disks) and when the device is not
in use.
Always make sure the polishing disk is not contaminated with abrasive elements - this might scratch the
polished surface. Polishing substances, such as wax, paste or liquid should be applied to the polishing disk
and not on the polished surface. Start the car polisher only once the disk comes into contact with the
surface to be polished. Grip the car polisher firmly before starting it. Make sure the surface to be polished is
free from sharp edges or projections which might damage or break the polishing disk. Polishing disks should
be washed regularly or when required. Abrasive substances may adhere to a polishing disk saturated with
wax and scratch the polished surface.
Wash the surface before polishing. For best polishing results, make sure that the surface is clean - this also
reduces the risk of grime and small mechanical contaminants scratching the surface.
To start polishing, place the car polisher onto the surface to be polished and switch it on. Do not press the
car polisher into the polished surface - use circular movements without increasing pressure.
MSW-POL120C (6234) and MSW-POL60C (6235) models include two types of polishing bonnets: coarse
and soft. The coarse polishing bonnet is used to distribute the polishing substance and the soft polishing
bonnet is for polishing. Make sure that the polishing bonnet is aligned evenly on the disk.
The polishing sponge is attached to the disk using Velcros. To replace
the disk, disconnect the device from the power source, insert
spanner (included) between the disk and the device (preventing the
disk from rotating) and unscrew the disk by hand.
MAINTENANCE AND INSPECTION
1.
Inspection of the machine
Never use damaged tools. Inspect the machine, together with its instrumentation, before each use.
2.
Inspection of the mounting screws
Inspect regularly all mounting screws and ensure that they are properly tightened. Should any of the
screws be loose, retighten them immediately. Failure to do so could result in serious hazards.
3.
Maintenance of the motor
To avoid damaging the motor, make sure that the device does not come into contact with oil or water.
4.
Always disconnect the machine from the power source before inspecting or repairing it.
5.
Keep the machine clean and pay particular attention to making sure that the vents are not clogged. The
vents should be cleaned after every use of the machine.
6.
Service: When repairing the machine, use only identical replacement parts. In such case please contact
our service centre. The use of any other part can lead to accidents or damage the tool. Do not
attempt to modify tools or create accessories not recommended. Such activities or reconstructions
are not allowed and could result in a hazardous condition leading to possible serious injury. It will also
void the warranty.
Rev. 10.05.2017
Rev. 10.05.2017
1
2
13
