background image

Model

 

407780

EN

 

v2.3

   

1/14

 

 

5

Operation 

This meter can be used in two different manners. As an Integrating Sound Level Meter or as a 
Sound Pressure Meter (SPL). 

Integrating Sound Level Meter 

LEQ Mode 

In the

 LEQ

 mode the display indicates the integrated (average) level for the run period. If no run time 

has been accumulated the display shows dashes. 

Taking Measurements 

 
1. 

Turn the meter on by pressing the 

green on/off

 button. 

2. 

Select the LEQ mode by pressing the 

Leq SEL SPL

 button until LEQ appears on the LCD. 

3. 

Select the desired Frequency Weighting as needed (A or C). 
Change the Frequency Weighting by pressing the '

A/C

' button. The 

'

A' or 

'

C' icon will display on 

the right-hand area of the LCD. 

4. 

Select the desired Response Time as needed (Fast or Slow) 
Change the Response Time by pressing the '

FAST/SLOW/IMPULSE

' button. The 'FAST'  

'SLOW' icon will display on the upper area of the LCD. 

5. 

Select the desired Run Time. There are 13 preset time settings available (To perform a manual 
recording select the 24 hour interval.)  

 

 

 

 

Change the run time by pressing the 

INTEG TIME

 button. The run time will appear in the middle 

of the LCD. Press the 

or

 button to select the preset time setting. 

6. 

Hold the instrument comfortably in hand and away from your body or position it on a tripod. Point 
the microphone toward the noise source 

7. Press 

  button to begin measuring. The run time counter will zero 

and begin counting. While running the meter will display 

 at the top 

of the display.  

 
 

The meter will stop automatically after the preset time interval has 
expired and will display 

 and the LEQ for the recording interval. 

 
To take another LEQ simply press 

 again. 

 
It is also possible to record each session. Simply press 

RECORD 

before

 

pressing 

. The 

RECORD icon will appear on the bottom right of the display and flash while the session is in 
progress. For instructions on retrieving the recorded data please refer to the software manual on 
the CD included with your meter.

 

1 second 

3 seconds 

10 seconds 30 

seconds 1 

minute 

5 minutes 

8 minutes 

10 minutes 30 

minutes 15 

minutes 

30 minutes 

1 hour 

8 hours 

24 hours 

 

Leq

00:00:30

68.7

dB

Leq

00:00:00

68.7

dB

Summary of Contents for 407780













Reviews: