background image

412355A-EU-EN v3.3   07/13 

Specifications 

General Specifications 
 

Display 

9999 count LCD  

Meter Power 

9 volt battery or 9V AC adaptor  

Auto Power OFF 

Meter automatically powers off after 10 minutes of inactivity 

Current output capability 

24mA at 1000 ohms

  

Operating Temperature   

5ºC to 40ºC (41ºF to 104ºF) 

Storage Temperature 

-20

o

C to 60

o

C (-4

o

F to 140

o

F) 

Operating Humidity 

Max 80% up to 31ºC (87ºF) decreasing linearly to 50% at 40ºC 
(104ºF) 

Storage Humidity 

<80%  

Operating Altitude 

2000meters (7000ft) maximum 

Dimensions 

96 x 118 x 45mm (3.8 x 4.7 x 1.8”) folded 

Weight 

340g (12 oz) 

Accessories Supplied 

9V battery, AC adaptor and calibration cable with spade lugs 

 

Range Specifications 

 

Mode 

Function 

Range 

Resolution 

Accuracy (% of reading) 

Measure 

Voltage 

0 to 2000mV 

1mV 

± (0.075% + 1 digit) or ± 3 
digits, whichever is greater 

2.00 to 20.00V 

0.01V 

Current 

0.00 to 50.00mA 

0.01mA 

-25.0 to 230.0% 

0.1% 

Source 

Voltage 

0 to 2000mV 

1mV 

2.00 to 20.00V 

0.01V 

Current 

0.00 to 24.00mA 

0.01mA 

-25.0 to 125.0% 

0.1% 

 

 
 
 

Copyright

 

©

 

2013

 

FLIR

 

Systems,

 

Inc.

 

All

 

rights

 

reserved

 

including

 

the

 

right

 

of

 

reproduction

 

in

 

whole

 

or

 

in

 

part

 

in

 

any

 

form

 

ISO

9001

 

Certified

 

www.extech.com

 

 

 

Summary of Contents for 412355A Oyster Series







Reviews: