background image

Model 42582  Version 6.0  Sept 2007 

10 

Specifications 

General Specifications 

Display 

  Backlit 

Multi-function 

LCD 

Over range indication 

"-------" appears on the LCD 

Printer 

  38mm 

Printer 

PC Interface 

 

RS-232C (TTL level) 

Datalogger memory 

12,000 readings 

Low battery indication 

Battery symbol appears on the LCD 

Power supply 

 

Four (4) 1.5V ‘AA” batteries or optional 9V (1000mA) adapter 

Operating current  

500mA (printing), 6mA (IR active), 2mA (IR standby)  

Auto Power OFF  

Adjustable from 1 to 20 minutes 

Operating Temperature 

32 to 122

o

F (0 to 50

o

C) 

Operating Humidity 

90% Relative Humidity maximum 

Dimensions/Weight 

8.2 x 2.8 x 2.1” (208 x 70 x 53mm) / 9.2 oz. (260g) with battery 

 

IR Measurement Specifications 

IR Measurement ranges 

-40 to 932

o

F (-40 to 500

o

C) 

Accuracy: 

-4 to 749ºF (-20 to 399

o

C); ±(2% of r 2 digit) or 

±4ºF/2ºC (whichever is greater) 

 

 

 

-40 to -3ºF (-40 to -19

o

C); ±6ºF/3ºC 

 

 

 

750ºF to 932ºF (400 to 500

o

C); ±(4% of r 2 digit) 

Resolution  

0.1

for displays <212

o

, otherwise 1

 

Repeatability  

±1

o

 

IR distance ratio   

8:1 

Response time   

0.2 seconds 

Emissivity 

 

Adjustable from 0.3 to 1.0 

 

External Probe Measurement Specifications 

Probe Measurement range  -4 to 302

o

F (-20 to 150

o

C) 

Accuracy: 

-4 to 32ºF (-20 to 0

o

C); ±2.2ºF (1.2ºC) 

 

 

 

33 to 122ºF (1 to 50

o

C); ±1.4ºF (0.8ºC) 

 

 

 

123 to 212ºF (51 to 100

o

C); ±2.8ºF (1.6ºC) 

 

 

 

213 to 302ºF (101 to 150

o

C); ±5.4ºF (3ºC) 

Resolution  

0.1

for displays <212

o

, otherwise 1

o

 

 

查询"42582"供应商

Summary of Contents for 42582















Reviews: