background image

 

AC or DC Current Measurements 

CAUTION

: Do not make current measurements on the 20A scale for longer than 30 seconds. Exceeding 30 seconds 

may cause damage to the meter and/or the test leads. 

1. 

Insert the black test lead into the negative 

COM

 jack. 

2.  For current measurements up to 4000

µ

A, set the function switch to the "

µ

A

" position and insert the red test lead 

into the 

mA-

µ

A

 jack. 

3.  For current measurements up to 400mA, set the function switch to the "

mA

" position and insert the red test lead 

into the 

mA-

µ

A

 jack.  

4.  For current measurements up to 20A AC, set the function switch to the "

20A

" position and insert the red test lead 

into the 

20A

 jack. 

5.  Press the DC/AC key until "

AC or DC

" appears on the display. 

6.  Remove power from the circuit under test and open the circuit at the point where you wish to measure current.  
7.  Touch the black test probe tip to the negative side of the circuit and touch the red test probe tip to the positive side 

of the circuit. 

8.  Apply power to the circuit. 
9.  Read the current in the display. 

Summary of Contents for MultiTec MT310



















Reviews: