background image

 

 

Tech Support 

Hotlines 

781-890-7440 

ext. 200 

extech@extech.com

 

t h

WARRANTY 

EXTECH INSTRUMENTS CORPORATION warrants this instrument to be free of defects in parts and workmanship for 
three years from date of shipment (a six month limited warranty applies on sensors and cables). If it should become 
necessary to return the instrument for service during or beyond the warranty period, contact the Customer Service 
Department at (781) 890-7440 ext. 210 for authorization. 

A Return Authorization (RA) number must be issued before 

any product is returned to Extech.

 The sender is responsible for shipping charges, freight, insurance and proper 

packaging to prevent damage in transit. This warranty does not apply to defects resulting from action of the user such as 
misuse, improper wiring, operation outside of specification, improper maintenance or repair, or unauthorized modification. 
Extech specifically disclaims any implied warranties or merchantability or fitness for a specific purpose and will not be 
liable for any direct, indirect, incidental or consequential damages. Extech's total liability is limited to repair or replacement 
of the product. The warranty set forth above is inclusive and no other warranty, whether written or oral, is expressed or 
implied.

 

REPAIR AND CALIBRATION SERVICES 

Extech offers complete repair and calibration services

 for all of the products we sell. 

For periodic calibration, NIST certification or repair of any Extech product, call customer 
service for details on services available. Extech recommends that calibration be performed 
on an annual basis to insure calibration integrity. 

Copyright © 1999 Extech Instruments Corporation. All rights reserved including the 
right of reproduction in whole or in part in any form.                             Version 1.2 4/00

 

Summary of Contents for MultiTec MT310



















Reviews: