background image

pH300   V1.0    7/09 

11

 

Support line (781) 890-7440 

Technical Support: Extension 200; E-mail: support@extech.com 

Repair & Returns: Extension 210; E-mail: repair@extech.com 

Product specifications subject to change without notice 

For the latest version of this User Guide, Software updates, and other 

up-to-the-minute product information, visit our website: www.extech.com 

Extech Instruments Corporation, 285 Bear Hill Road, Waltham, MA 02451 

ISO9001 Certified 

Warranty 

EXTECH INSTRUMENTS CORPORATION 

(A FLIR COMPANY)

 

warrants this instrument to be free of 

defects in parts and workmanship for one year from date of shipment (a six month limited warranty 
applies to sensors and cables). If it should become necessary to return the instrument for service during 
or beyond the warranty period, contact the Customer Service Department at (781) 890-7440 ext. 210 for 
authorization or visit our website www.extech.com for contact information. A Return Authorization (RA) 
number must be issued before any product is returned to Extech. The sender is responsible for shipping 
charges, freight, insurance and proper packaging to prevent damage in transit. This warranty does not 
apply to defects resulting from action of the user such as misuse, improper wiring, operation outside of 
specification, improper maintenance or repair, or unauthorized modification. Extech specifically 
disclaims any implied warranties or merchantability or fitness for a specific purpose and will not be liable 
for any direct, indirect, incidental or consequential damages. Extech's total liability is limited to repair or 
replacement of the product. The warranty set forth above is inclusive and no other warranty, whether 
written or oral, is expressed or implied. 

 

Calibration and Repair Services 

Extech offers repair and calibration services

 for the products we sell. Extech also 

provides NIST certification for most products. Call the Customer Care Department for 
information on calibration services available for this product. Extech recommends that 
annual calibrations be performed to verify meter performance and accuracy. 
 
 

 

 

 
 
 
 
 
 
 
 
 

Copyright 

©

 2009 Extech Instruments Corporation (a FLIR company) 

All rights reserved including the right of reproduction in whole or in part in any form. 

www.burntec.com

Summary of Contents for pH300













Reviews: