background image

pH300   V1.0    7/09 

pH Measurement Mode 

Preparation for Measurement 

1.  Turn the meter ON using the power key 
2.  Press the MODE key momentarily to switch to the pH mode, if necessary 
3.  Unscrew the protective cap on the probe jack located on the bottom of the meter (store 

the protective cap in the carrying case for later use) 

4.  Carefully connect the pH probe to the meter’s probe jack. The probe can only be 

inserted in one orientation. Once it is firmly connected, screw the probe collar onto the 
meter to secure the probe. 

3-Point Calibration (7.00pH, 4.00pH and 10.01pH) 

Note: Calibrate the unit once per day for best results. 

 

1. Press the 

CAL

 key to enter the Calibration mode. The meter’s display will show a 

blinking ‘

Cl

’ 

2.  Rinse the probe in distilled water, allow it to dry, and submerge it into a pH 7.00 buffer 

solution. Stir the solution briefly and allow it to stay in the buffer solution until a stable 
reading is reached 

3. Press 

CAL

 again and the display will show a blinking ‘

7.00’

 

4.  This portion of the calibration procedure is complete when the display stops blinking 

and shows the ‘

C2

’ icon. The unit will automatically switch to the second point of the 

calibration 

5.  Rinse the probe in distilled water again, allow it to dry, and submerge it into a pH 4.00 

buffer solution. Stir the solution briefly and allow it to stay in the buffer solution until a 
stable reading is reached 

6. Press 

CAL

 again and the display will show a blinking ‘

4.00’

 

7.  This portion of the calibration procedure is complete when the display stops blinking 

and shows the ‘

C3

’ icon. The unit will automatically switch to the third point of the 

calibration 

8.  Rinse the probe in distilled water again, allow it to dry, and submerge it into a pH 10.01 

buffer solution. Stir the solution briefly and allow it to stay in the buffer solution until a 
stable reading is reached 

9. Press 

CAL

 again and the display will show a blinking ‘

10.01

’ 

10. After the display stabilizes the 3-point calibration icon will appear 

 

1-Point and 2-Point Calibration 

Note that the user can calibrate one or two points only, if the expected measurement is 
known. 
For example, if the expeced pH is 4pH, it is acceptable to perform only a 1-Point 
Calibration (4pH). If the expected measurement is between 4.00pH and 7.00pH, the user 
can perform a 2-Point Calibration (4.00 and 7.00pH), and so on. 
For a 4pH calibration, only the circled 

L

 will appear on the LCD. For a 7.00pH, only the 

circled 

M

 will appear on the LCD. For a 10.01pH Calibration, only the circled 

H

 will appear 

(

L

ow, 

M

edium, and 

H

igh). 

For all other applications, a 3-Point Calibration is recommended. Always perform a 3-Point 
Calibration on new probes and probes that have been in use for long periods. This 
maximizes measurement slope linearity. 

www.burntec.com

Summary of Contents for pH300













Reviews: