background image

Version 3.1   1/06 

 

Support line (781) 890-7440 

Technical support: Extension 200; E-mail: support@extech.com 

Repair & Returns: Extension 210; E-mail: repair@extech.com 

 

Product specifications subject to change without notice 

 

For the latest version of this User’s Guide, Software updates, and other 

up-to-the-minute product information, visit our website: www.extech.com 

Battery Replacement 

AC power is the normal power source for this meter. If 8 AA batteries are used, they are 
located in the rear battery compartment. When the battery icon appears on the meter's 
LCD, it is time to replace the batteries. 

1. Turn  power  off. 

2. Open the rear battery cover  

3. Insert the batteries into battery holder, observing the correct polarity. 

4. Put the battery cover back in place. 

 

Calibration and Repair Services 

Extech offers complete repair and calibration services

 for all of the products we sell. 

For periodic calibration, NIST certification or repair of any Extech product, call customer 
service for details on services available. Extech recommends that calibration be performed 
on an annual basis to insure calibration integrity. 
 
 
 
 
 
 
 
 
 

 
 

Warranty 

EXTECH INSTRUMENTS CORPORATION warrants this instrument to be free of defects in parts and 
workmanship for one year from date of shipment (a six month limited warranty applies on sensors and 
cables). If it should become necessary to return the instrument for service during or beyond the warranty 
period, contact the Customer Service Department at (781) 890-7440 ext. 210 for authorization or visit our 
website at www.extech.com  (click on ‘Contact Extech’ and go to Service Department to request an RA 
number). A Return Authorization (RA) number must be issued before any product is returned to Extech. The 
sender is responsible for shipping charges, freight, insurance and proper packaging to prevent damage in 
transit. This warranty does not apply to defects resulting from action of the user such as misuse, improper 
wiring, operation outside of specification, improper maintenance or repair, or unauthorized modification. 
Extech specifically disclaims any implied warranties or merchantability or fitness for a specific purpose and 
will not be liable for any direct, indirect, incidental or consequential damages. Extech's total liability is limited 
to repair or replacement of the product. The warranty set forth above is inclusive and no other warranty, 
whether written or oral, is expressed or implied. 

 
 
 
 
 
 

Copyright 

©

 

2006 Extech Instruments Corporation. 

All rights reserved including the right of reproduction in whole or in part in any form.

 

Summary of Contents for SL130









Reviews: