71
70
EN
EN
CONTACT DETAILS FOR NEW ZEALAND
Distributor
: Madal Bal NZ, 57 Grey Street, Onehunga, Auckland, New Zealand 1061
E-mail: madalbal@madalbal.co.nz
EU Declaration of Conformity
Manufacturer: Madal Bal a.s. Bartošova 40/3, CZ-760 01 Zlín • Company ID No.: 49433717
hereby declares
that the devices designated below, based on its concept and design, as well as designs sold on the market,
comply with applicable safety requirements of the European Union.
This declaration becomes void in the event of modifications to the product that are not approved by us.
This declaration is issued under the exclusive responsibility of the manufacturer.
Extol Premium 8890207, 8890101, 8890210
Extol Craft 401232
Chiselling and drilling hammers
Harmonised standards (including their amendments, if any exist), which were used
in the assessment of conformity and on the basis of which the Declaration of conformity is issued:
EN 62841-1:2015, EN IEC 62841-2-6:2020, EN 55014-1:2017; EN 55014-2:2015;
EN IEC 61000-3-2:2019; EN 61000-3-3:2013; EN IEC 63000:2018, EN ISO 3744:2010
and harmonisation directives:
2006/42 ES; 2014/30 EU; 2000/14 ES; 2011/65 EU
Measured level of acoustic power of the equipment representing the given model: see chapter Technical specifications
Guaranteed acoustic power level of the equipment: 101 dB(A)
The technical documentation 2006/42 ES, 2000/14 ES was drawn up by Martin Šenkýř at the address of Madal Bal , a.s.,
Průmyslová zóna Příluky 244, 760 01 Zlín, Czech Republic. The Technical Documentation (2006/42 ES, 2000/14 ES)
is available at the above address of Madal Bal, a.s. Conformity assessment procedure (2006/42 ES, 2000/14 ES)
Verification of the individual products by the notified entity no.: 0123 TÜV SÜD Product Service GmbH, Riedlerstrasse 65,
Zertifizierstellen, 80339 München, Germany.
Place and date of issue of EU Declaration of Conformity:
Zlín 27.7.2020
Person authorised to write up the EU Declaration of Conformity on behalf of the manufacturer (signature, name, function):
Martin Šenkýř
Member of the Board of the manufacturer
y
Ensure that the SDS clamping head is free of stones,
construction dust or other abrasive materials created
during chiselling/drilling, since these damage the
clamping system.
y
Keep the motor vents clean, otherwise the motor may
overheat as a result of insufficient air flow.
y
To clean the surface of the hammer drill, use a damp
cloth dipped in, for example, soapy water. Ensure that no
water enters into the internal area of the hammer drill.
y
Do not use organic solvents for cleaning, e.g. based on
acetone, abrasive cleaning agents or agents with oxida-
tion properties, since they would damage the surface of
the hammer drill.
y
Free warranty repairs relate only to manufacturing
defects on the product (hidden and external) and do
not relate to the wear of the product as a result of
excessive load or normal use or damage of the product
caused by incorrect use.
y
In the event of a dispute between the buyer and the
vendor in respect to the purchase contract that was not
resolved directly between the parties, the buyer has
the right to the trade inspection authority for an out-
-of-court settlement of the a consumer dispute. At the
website of the trade inspection authority there is a link
to the tab „ADR-amicable dispute resolution“.
X. Storage
y
Store the cleaned power tool in a safe location that is out
of reach of children where temperatures do not exceed
45°. Protect the power tool against direct sunlight,
radiant heat sources, humidity and ingression of water.
XI. Waste disposal
y
Throw packaging materials into a container for the
respective sorted waste.
The product contains electronic
components that constitute hazardous
waste. According to European Directive
No. 2012/19 EU, electric appliances must
not be thrown out with household
waste, and must be handed over for
ecological disposal at specified
collection points. You can find information about these
collection points at your local town council office.
