manualshive.com logo in svg

Extreme Networks ExtremeWare 7.5, Command Reference Manual

Download the free Command Reference Manual for Extreme Networks ExtremeWare 7.5, an advanced networking solution. This comprehensive manual provides detailed instructions and information on utilizing the product's functionalities. Enhance your networking experience by accessing the manual from 88.208.23.73:8080.

Share
Download
background image

 

1074

ExtremeWare 7.5 Command Reference Guide

Security Commands

unconfigure enhanced-dos-protect ipfdb learn-limit

unconfigure enhanced-dos-protect ipfdb learn-limit ports <portlist> 

Description

Resets the learning limit for enhanced denial of service protection to default parameter values for the 
selected ports.

Syntax Description

Default

The default learn-limit on Fast Ethernet ports is 100 pkts/learn window.

 

The default learn-limit on Gigabyte ports is 100 pkts/learn window.

Usage Guidelines

Use this command to reset to default the learning limit value that defines the number of packets to be 
counted before ExtremeWare can create an IPFDB entry in the hardware.

To configure the learning limit on untrusted ports for enhanced denial of service protection, use the 
following command:

configure enhanced-dos-protect ipfdb learn-limit

Usage Guidelines

Use this command to reset the learning limit value to the default number of packets being counted 
before the software can create an entry in hardware.

Example

The following command resets the learn limit on Fast Ethernet port 3 to 100 packets within the learning 
window before an IPFDB entry can be created:

unconfigure enhanced-dos-protect ipfdb learn-limit ports 3

History

This command was first available in ExtremeWare 7.3.0.

This command was added to the Summit “

e

” series of switches in ExtremeWare 7.3e.

Platform Availability

This command is available on all platforms.

portlist

Specifies one or more ports or slots and ports. On a modular switch, can be a list of slots and ports. 
On a stand-alone switch, can be one or more port numbers. May be in the form 1, 2, 3-5, 2:*, 2:5, 
2:6-2:8. 

Summary of Contents for ExtremeWare 7.5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExtremeWare 7.5

Sony Ericsson Controller Mode Application Note preview
Controller Mode
Brand: Sony Ericsson Pages: 10
Juniper JUNOSE 11.2 Configuration Manual preview
JUNOSE 11.2
Brand: Juniper Pages: 772
3Com 3CR15800 - Intelligent Management Center Enterprise... Datasheet preview
3CR15800 - Intelligent Management Center Enterprise...
Brand: 3Com Pages: 4
Nortel SCS User Manual preview
SCS
Brand: Nortel Pages: 41
Nortel BayStack 380-24F Getting Started preview
BayStack 380-24F
Brand: Nortel Pages: 76
Nortel Attendant PC Software User'S Manual preview
Attendant PC
Brand: Nortel Pages: 176
Nortel Express Call Center User Manual preview
Express Call Center
Brand: Nortel Pages: 638
Nortel Symposium Web Center Portal Installation And Administration Manual preview
Symposium Web Center Portal
Brand: Nortel Pages: 710
M-Audio Jamlab User Manual preview
Jamlab
Brand: M-Audio Pages: 15
EVGA PC-over-IP Administrative Interface User Manual preview
PC-over-IP Administrative Interface
Brand: EVGA Pages: 108
I.R.I.S. READIRIS PRO 12 Getting Started Manual preview
READIRIS PRO 12
Brand: I.R.I.S. Pages: 10
I.R.I.S. IRISPowerscan 9.5 User Manual preview
IRISPowerscan 9.5
Brand: I.R.I.S. Pages: 182
THOMSON LCP 400 User Manual preview
LCP 400
Brand: THOMSON Pages: 22
UNIBLUE PowerSuite 2010 Product Manual preview
PowerSuite 2010
Brand: UNIBLUE Pages: 13
MACROMEDIA FLASH 8-FLASH Use Manual preview
FLASH 8-FLASH
Brand: MACROMEDIA Pages: 678
Sun Microsystems VIRTUALBOX 3.0.0 User Manual preview
VIRTUALBOX 3.0.0
Brand: Sun Microsystems Pages: 259
Bay Networks BayRS Notice preview
BayRS
Brand: Bay Networks Pages: 104
MACROMEDIA BREEZE PRESENTER Manual preview
BREEZE PRESENTER
Brand: MACROMEDIA Pages: 106

Brands by name

Popular brands

Load more brands