manualshive.com logo in svg

Extreme Networks ExtremeWare 7.5, Command Reference Manual

Download the free Command Reference Manual for Extreme Networks ExtremeWare 7.5, an advanced networking solution. This comprehensive manual provides detailed instructions and information on utilizing the product's functionalities. Enhance your networking experience by accessing the manual from 88.208.23.73:8080.

Share
Download
background image

 

1170

ExtremeWare 7.5 Command Reference Guide

Troubleshooting Commands

configure debug-trace npcard

configure debug-trace npcard <debug level>

Description

This command enables system-level debug tracing for the MPLS, PoS, ARM, and ATM modules.

NOTE

This command is available only on the MPLS, PoS, ARM, and ATM modules for the “i” series switches.

Syntax Description

Default

The default level is 0.

Usage Guidelines

The 

debug level

 range is 1 to 5. Higher levels record more verbose messages. Higher levels also record 

the messages recorded at lower levels.

Example

The following command sets the reporting level for module errors to 3:

configure debug-trace npcard 3

History

This command was first available in an ExtremeWare IP Technology Services Release based on 
ExtremeWare v6.1.8b12.

Platform Availability

This command is available on the MPLS, PoS, ARM, and ATM modules.

debug level

Specifies a debug level:

0—

Indicates that a severe event has occurred that most likely will result in the termination or 
improper operation of the ARM.

1—

Indicates that a major event has occurred. It may represent a negative operation. It should 
be reviewed to ensure proper continuation of ARM operation.

2—

Indicates a minor event has occurred.

3—

Provides additional information to support engineers for the purpose of diagnosing network 
problems.

4 —

No additional information recorded.

5 —

No additional information recorded.

Summary of Contents for ExtremeWare 7.5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExtremeWare 7.5

Canon 70 MC - ZR70MC MiniDV Digital Camcorder Instruction Manual preview
70 MC - ZR70MC MiniDV Digital Camcorder
Brand: Canon Pages: 57
Canon PowerShot A410 Software Starter Manual preview
PowerShot A410
Brand: Canon Pages: 106
Samsung UN40C7000WF User Manual preview
UN40C7000WF
Brand: Samsung Pages: 7
FARONICS DEEP FREEZER PROFESSIONAL Manual preview
DEEP FREEZER PROFESSIONAL
Brand: FARONICS Pages: 31
KAPERSKY ANTI-VIRUS 5.1 - FOR MICROSOFT ISA SERVER Administrator'S Manual preview
ANTI-VIRUS 5.1 - FOR MICROSOFT ISA SERVER
Brand: KAPERSKY Pages: 67
Red Hat ENTERPRISE LINUX WS 2.1 - Installation Manual preview
ENTERPRISE LINUX WS 2.1 -
Brand: Red Hat Pages: 110
Elgato EyeTV Hybrid Hardware Reference Manual preview
EyeTV Hybrid
Brand: Elgato Pages: 5
MACROMEDIA Director MX Use Manual preview
Director MX
Brand: MACROMEDIA Pages: 624
Navman SmartST 2009 User Manual preview
SmartST 2009
Brand: Navman Pages: 82
Intel ITANIUM ARCHITECTURE - SOFTWARE DEVELOPERS VOLUME 3 REV 2.3 Manual preview
ITANIUM ARCHITECTURE - SOFTWARE DEVELOPERS VOLUME 3 REV 2.3
Brand: Intel Pages: 1898
GRASS VALLEY EDIUS Edit Station Datasheet preview
EDIUS Edit Station
Brand: GRASS VALLEY Pages: 4
VERITEQ vLog 4.4 User Manual preview
vLog 4.4
Brand: VERITEQ Pages: 112
Autodesk ARCHITECTURE 2010 Brochure preview
ARCHITECTURE 2010
Brand: Autodesk Pages: 4
LaCie 4L User Manual preview
4L
Brand: LaCie Pages: 6
MACROMEDIA COLDFUSION MX 61-CFML Reference preview
COLDFUSION MX 61-CFML
Brand: MACROMEDIA Pages: 806
FARONICS CORE Manual preview
CORE
Brand: FARONICS Pages: 99
D-Link DS-601 - VPN Client - PC Product Data Sheet preview
DS-601 - VPN Client - PC
Brand: D-Link Pages: 2
Canon Powershot S80 Software User'S Manual preview
Powershot S80
Brand: Canon Pages: 157

Brands by name

Popular brands

Load more brands