Extreme Networks ExtremeWare 7.5 Command Reference Manual Download | Manualshive

Page: 1212 / 2546

background image

1212

ExtremeWare 7.5 Command Reference Guide

Troubleshooting Commands

run diagnostics cable ports

run diagnostics cable ports <portlist>

Description

Runs diagnostics on Ethernet cables.

Syntax Description

Default

N/A

Usage Guidelines

This command tests each of the four unshielded twisted-pair (UTP) cables. When the test completes, the
command prompts you to enter the show port

portlist

cable diagnostics command to see the results

of the test.

By reviewing the output of the

show

command you can determine:

•

The length of the cable

•

Whether there is a successful termination, or whether there is an open or short

Examples

The following example tests the Ethernet cable inserted into port 1. The four copper pairs do not all
have the same length, which might indicate a kink in the cable, or a open connection:

Summit400-48t:27 # run diagnostics cable ports 1

Cable Diagnostics has completed, to view results enter

show port <port list> cable diagnostics

Summit400-48t:28 # show port 1 cable diagnostics

Port

Pair

Length

Status

1

Pair A

3 meters

Terminated

Pair B

2 meters

Terminated

Pair C

1 meters

Open or Short

Pair D

1 meters

Open or Short

The following example shows none of the twisted pairs terminate successfully at port 1, which could
indicate that the cable is not inserted into the port:

Summit400-48t:29 # run diagnostics cable ports 1

Cable Diagnostics has completed, to view results enter

show port <port list> cable diagnostics

portlist

Runs cable diagnostics for one or more port numbers.

«
...
1210
1211
1212
1213
1214
...
»

Summary of Contents for ExtremeWare 7.5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExtremeWare 7.5

Brand: NEC Pages: 81

Brand: MAGIX Pages: 88

eXpress Altris eXpress Helpdesk Solution 5.6 SP1

Brand: altiris Pages: 143

Brand: SanDisk Pages: 11

Brand: Campbell Pages: 16

SNAP DEPLOY 2.0 -

Brand: ACRONIS Pages: 68

NETWORK BASIC - USER REFERENCE GUIDE 3.2

Brand: Red Hat Pages: 76

Brand: Southern Company Pages: 13

Ohioedge CRM+BPM

Brand: Source Technologies Pages: 36

Brand: Ulead Pages: 100

READIRIS PRO 12

Brand: I.R.I.S. Pages: 10

Topo North America 9.0

Brand: DeLorme Pages: 257

Brand: AMX Pages: 24

Brand: GRASS VALLEY Pages: 2

Brand: UNIBLUE Pages: 4

SystemTweaker 2010

Brand: UNIBLUE Pages: 13

Brand: FieldServer Pages: 51

Brand: Darim Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands