manualshive.com logo in svg

Extreme Networks ExtremeWare 7.5, Command Reference Manual

Download the free Command Reference Manual for Extreme Networks ExtremeWare 7.5, an advanced networking solution. This comprehensive manual provides detailed instructions and information on utilizing the product's functionalities. Enhance your networking experience by accessing the manual from 88.208.23.73:8080.

Share
Download
background image

 

This command is available on the Summit 300-48, Summit 300-24, Summit 400-24p and Alpine switches.enable wireless ports interface svp

ExtremeWare 7.5 Command Reference Guide

1323

This command is available on the Summit 300-48, Summit 300-24, Summit 400-24p and Alpine 

switches.

enable wireless ports interface svp

enable wireless ports [<portlist> | all] interface [1 | 2] svp

Description

Enables the QoS protocol, SpectraLink Voice Protocol (SVP), for VoIP on the specified port and interface.

Syntax Description

Default

Disabled

Usage Guidelines

Use this command to implement the QoS protocol for VoIP. By enabling QoS for VoIP, you give voice 
traffic a higher priority than data traffic. VoIP traffic has less tolerance for error recovery than data. 
Although voice traffic can tolerate some degree of error recovery, it can be noticeable to users. This 
command allows you to enable QoS for VoIP on the port and interface level.

Example

The following example, turns on SVP on port 17 and interface 1:

enable wireless ports 17 interface 1 svp

History

This command was first available in ExtremeWare 7.3e.

Platform Availability

This command is available on the Summit 300-48, Summit 300-24, Summit 400-24p and Alpine switches.

portlist

Specifies one or more ports or slots and ports. an be one or more port numbers. May be in the form 
1, 2, 1:2, 3-5. 

all

Specifies all ports.

interface

Specifies an interface: 1 or 2.

Summary of Contents for ExtremeWare 7.5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExtremeWare 7.5

Samsung SL-M2820DW Driver Manual preview
SL-M2820DW
Brand: Samsung Pages: 16
Samsung SCX 4826FN - Laser Multi-Function Printer Brukerhåndbok preview
SCX 4826FN - Laser Multi-Function Printer
Brand: Samsung Pages: 16
Yamaha DM 1000 Manual preview
DM 1000
Brand: Yamaha Pages: 30
F-SECURE ANTI-VIRUS FOR MIMESWEEPER - Administrator'S Manual preview
ANTI-VIRUS FOR MIMESWEEPER -
Brand: F-SECURE Pages: 44
Omron WS02-NCTC1-E - 07-2001 Operation Manual preview
WS02-NCTC1-E - 07-2001
Brand: Omron Pages: 116
Citrix MetaFrame MetaFrame Presentation Server Reviewer'S Manual preview
MetaFrame MetaFrame Presentation Server
Brand: Citrix Pages: 97
Alpha Moisture Systems SADPmini Logger Instruction Manual preview
SADPmini Logger
Brand: Alpha Moisture Systems Pages: 14
Symantec WISE INSTALLATION EXPRESS 7.0 SP2 Getting Started Manual preview
WISE INSTALLATION EXPRESS 7.0 SP2
Brand: Symantec Pages: 50
Sony D-NF610 - Portable Cd Player Specifications preview
D-NF610 - Portable Cd Player
Brand: Sony Pages: 1
Sony D-NF420 - Portable Cd Player Specifications preview
D-NF420 - Portable Cd Player
Brand: Sony Pages: 2
Sony D-NE718CK - Portable Cd Player Specifications preview
D-NE718CK - Portable Cd Player
Brand: Sony Pages: 2
Sony D-NE520 - Atrac Cd Walkman Portable Player Specifications preview
D-NE520 - Atrac Cd Walkman Portable Player
Brand: Sony Pages: 2
Sony CPF-IX001 - Wireless PC-Linked Audio System Installation Manual preview
CPF-IX001 - Wireless PC-Linked Audio System
Brand: Sony Pages: 2
Sony D-NE20 - Atrac Cd Walkman Installation & Operating Manual preview
D-NE20 - Atrac Cd Walkman
Brand: Sony Pages: 20
Sony D-NE718CK - Portable Cd Player Service Manual preview
D-NE718CK - Portable Cd Player
Brand: Sony Pages: 36
Sony D-NF420 - Portable Cd Player Service Manual preview
D-NF420 - Portable Cd Player
Brand: Sony Pages: 38
Sony D-NF610 - Portable Cd Player Operating Instructions Manual preview
D-NF610 - Portable Cd Player
Brand: Sony Pages: 40
Sony D-NE329SP - Atrac Cd Walkman Portable Player Operating Instructions Manual preview
D-NE329SP - Atrac Cd Walkman Portable Player
Brand: Sony Pages: 39

Brands by name

Popular brands

Load more brands