Extreme Networks ExtremeWare 7.5 Command Reference Manual Download | Manualshive

Page: 1408 / 2546

background image

1408

ExtremeWare 7.5 Command Reference Guide

EAPS Commands

configure eaps failtime

configure eaps <name> failtime [<seconds>]

Description

Configures the value of the failtimer the master node uses for EAPS health-check packets.

Syntax Description

Default

The default is three seconds.

Usage Guidelines

Use the

failtime

keyword and its associated

seconds

parameter to specify the amount of time the

master node waits before the failtimer expires. The

seconds

parameter must be set greater than the

configured value for

hellotime

. The default value is three seconds.

Increasing the

failtime

value provides more protection by waiting longer to receive a health-check

packet when the network is congested.

NOTE

In previous versions of ExtremeWare, the secondary port on the Master node would open when the
failtimer expired. In ExtremeWare 7.1 the default behavior has been modified to not open the secondary
port. You can configure the action taken when the failtimer expires by using the

configure eaps

failtime expiry-action

command.

Example

The following command configures the failtimer value for the EAPS domain “eaps_1” to 15 seconds:

configure eaps eaps_1 failtime 15

History

This command was first available in ExtremeWare 6.2.

The behavior for this command was modified in ExtremeWare 7.1 to follow the parameters configured
in

configure eaps failtime expiry-action

.

This command was added to the Summit “

e

” series of switches in ExtremeWare 7.2e.

Platform Availability

This command is available on all platforms.

name

Specifies the name of an EAPS domain.

seconds

Specifies the number of seconds the master node waits to receive a
health-check packet before the failtimer expires. Default is 3 seconds.

«
...
1406
1407
1408
1409
1410
...
»

Summary of Contents for ExtremeWare 7.5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExtremeWare 7.5

Brand: UMAX Technologies Pages: 10

Brand: Yamaha Pages: 37

Brand: ICP Pages: 77

Brand: AMX Pages: 50

Brand: SanDisk Pages: 11

Brand: CenturyLink Pages: 24

Brand: Brady Pages: 33

PCANYWHERE - V12.1

Brand: Symantec Pages: 321

Brand: DigiDesign Pages: 39

VANTAGE CNM 2.0 -

Brand: ZyXEL Communications Pages: 346

Brand: JETWAY Pages: 43

ANTI-VIRUS 2011 - REV 2011.11

Brand: AVG Pages: 209

Brand: CyberLink Pages: 75

Brand: DeLorme Pages: 437

Brand: Adaptec Pages: 6

IBM OS/2 v2.x & Warp

Brand: Adaptec Pages: 6

1210SA - Serial ATA RAID Controller

Brand: Adaptec Pages: 88

Brand: Wavecom Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands