1426
ExtremeWare 7.5 Command Reference Guide
EAPS Commands
Example
The following command displays detailed EAPS information for domain “eaps1”:
show eaps eaps1 detail
The results for domain “eaps1” on a master node are shown as follows:
Name: "eaps1" (instance=0)
State: Complete [Running: Yes]
Enabled: Yes Mode: Master
Primary port: 10 Port status: Up Tag status: Tagged
Secondary port: 20 Port status: Blocked Tag status: Tagged
Hello Timer interval: 1 sec Fail Timer interval: 3 sec
Fail timer expiry action: Send alert
Last update: From Master Id 00:04:96:18:40:92, at Wed Jan 28 15:58:20 2004
EAPS Domain has following Controller Vlan:
Vlan Name VID QosProfile
"cvlan" 0100 QP8
EAPS Domain has following Protected Vlan(s):
Vlan Name VID QosProfile
"pvlan" 0200 QP1
Number of Protected Vlans: 1
The following command displays detailed EAPS information:
show eaps detail
The results for a transit node are shown as follows:
EAPS Enabled: Yes
Number of EAPS instances: 1
EAPSD-Bridge links: 2
Name: “eaps1” (instance=0)
State: Links-Up [Running: Yes]
Enabled: Yes Mode: Transit
Primary port: 13 Port status: Up Tag status: Tagged
Failtimer expiry action:
Displays the action taken when the failtimer expires:
•
Send-alert—Sends a critical message to the syslog when the failtimer
expires.
•
Open-secondary-port—Opens the secondary port when the failtimer
expires.
Displays only for master nodes.
Preforwarding Timer interval:
1
The configured value of the timer. This value is set internally by the EAPS
software.
Last update:
1
Displayed only for transit nodes; indicates the last time the transit node
received a hello packet from the master node (identified by its MAC address).
EAPS Domain has … Controller
Vlans:
Lists the assigned name and ID of the control VLAN.
EAPS Domain has … Protected
Vlans:
2
Lists the assigned names and VLAN IDs of all the protected VLANs
configured on this EAPS domain.
Number of Protected Vlans:
The count of protected VLANs configured on this EAPS domain.
1.
These fields apply only to transit nodes; they are not displayed for a master node.
2.
This list is displayed when you use the
detail
keyword in the
show eaps
command.
Summary of Contents for ExtremeWare 7.5
