manualshive.com logo in svg

Extreme Networks ExtremeWare 7.5, Command Reference Manual

Download the free Command Reference Manual for Extreme Networks ExtremeWare 7.5, an advanced networking solution. This comprehensive manual provides detailed instructions and information on utilizing the product's functionalities. Enhance your networking experience by accessing the manual from 88.208.23.73:8080.

Share
Download
background image

 

1440

ExtremeWare 7.5 Command Reference Guide

STP Commands

•

pvst-plus

—This mode implements PVST+ in compatibility with third-party switches running this 

version of STP. The STPDs running in this mode have a one-to-one relationship with VLANs, and 
send and process packets in PVST+ format. 

An StpdID is used to identify each STP domain. You assign the StpdID when configuring the domain. 
An StpdID must be identical to the VLANid of one of the member VLANs in that STP domain, and that 
VLAN cannot belong to another STPD.

NOTE

These port modes are for STP ports, not for physical ports. When a physical port belongs to multiple 
STPDs, it is associated with multiple STP ports. It is possible for the physical port to run in different 
modes for different domains for which it belongs.

When the switch boots, it automatically creates a VLAN named default with a tag value of 1, and STPD 
s0 with an StpdID of 1. The switch associates VLAN default to STPD s0. By default, all ports that belong 
to this VLAN and STPD are in 802.1d mode.

Example

Create a VLAN named marketing and an STPD named STPD1 as follows:

create vlan marketing

create stpd stpd1

The following command adds the VLAN named marketing to the STPD STPD1

:

configure stpd stpd1 add vlan marketing

History

This command was first available in ExtremeWare 2.0.

This command was modified in ExtremeWare 6.2 to support STP port mode configurations.

This command was added to the Summit “

e

” series of switches in ExtremeWare 6.2a and ExtremeWare 

7.1e.

This command was modified in ExtremeWare 7.2e to support STP port mode configurations.

The default port mode also changed from dot1d to emistp in ExtremeWare 7.2e.

Platform Availability

This command is available on all platforms.

Summary of Contents for ExtremeWare 7.5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExtremeWare 7.5

ScanSoft DRAGON NATURALLYSPEAKING 7 User Manual preview
DRAGON NATURALLYSPEAKING 7
Brand: ScanSoft Pages: 222
Red Hat NETWORK SATELLITE SERVER 4.0.5 Installation Manual preview
NETWORK SATELLITE SERVER 4.0.5
Brand: Red Hat Pages: 82
AVIRA ANTIVIR VIRUS SCAN ADAPTER Configuration preview
ANTIVIR VIRUS SCAN ADAPTER
Brand: AVIRA Pages: 29
Xerox Integrated Fiery Color Server Quick Start Manual preview
Integrated Fiery Color Server
Brand: Xerox Pages: 24
Red Hat NETWORK 3.6 - Reference Manual preview
NETWORK 3.6 -
Brand: Red Hat Pages: 198
MACROMEDIA FLASH 8-LEARNING ACTIONSCRIPT 2.0 IN FLASH Manual preview
FLASH 8-LEARNING ACTIONSCRIPT 2.0 IN FLASH
Brand: MACROMEDIA Pages: 830
LinPlug MorphoX User Manual preview
MorphoX
Brand: LinPlug Pages: 46
eCopy ShareScan 4.2 Installation And Setup Manual preview
ShareScan 4.2
Brand: eCopy Pages: 266
Ulead BURN.NOW 1.5 User Manual preview
BURN.NOW 1.5
Brand: Ulead Pages: 60
Red Hat CERTIFICATE SYSTEM 7.3 - ADMINISTRATION Administration Manual preview
CERTIFICATE SYSTEM 7.3 - ADMINISTRATION
Brand: Red Hat Pages: 554
2Wire Third-Party Installation Manual preview
Third-Party
Brand: 2Wire Pages: 35
YASKAWA XTRAWARE - V3.0 Manual preview
XTRAWARE - V3.0
Brand: YASKAWA Pages: 263
3Com SUPERSTACK 3 WEBCACHE 3000 User Manual preview
SUPERSTACK 3 WEBCACHE 3000
Brand: 3Com Pages: 362
Native Instruments Studio Drummer User Manual preview
Studio Drummer
Brand: Native Instruments Pages: 41
Samsung ML 2510 - B/W Laser Printer Manual preview
ML 2510 - B/W Laser Printer
Brand: Samsung Pages: 33
Canon 2675B001 - SELPHY ES3 Photo Printer Software User'S Manual preview
2675B001 - SELPHY ES3 Photo Printer
Brand: Canon Pages: 49
Trend Micro Home Network Security Services Quick Start Manual preview
Home Network Security Services
Brand: Trend Micro Pages: 9
Alpine NVD-A211 SMART MAP PRO Owner'S Manual preview
NVD-A211 SMART MAP PRO
Brand: Alpine Pages: 95

Brands by name

Popular brands

Load more brands