manualshive.com logo in svg

Extreme Networks ExtremeWare 7.5, Command Reference Manual

Download the free Command Reference Manual for Extreme Networks ExtremeWare 7.5, an advanced networking solution. This comprehensive manual provides detailed instructions and information on utilizing the product's functionalities. Enhance your networking experience by accessing the manual from 88.208.23.73:8080.

Share
Download
background image

 

1510

ExtremeWare 7.5 Command Reference Guide

ESRP Commands

configure vlan add track-bgp 

configure vlan <vlan name> add track-bgp failover <priority>

Description

Configures an ESRP-enabled VLAN to track any available BGP route.

Syntax Description

Default

No BGP route tracking. 

Usage Guidelines

If no BGP routes are detected, the ESRP VLAN priority steps to the failover-priority value specified. By 
setting the failover priority to be lower than the normal priority of the VLAN, it will cause the affected 
VLAN to go into standby. 

The range of the priority value is 0 to 254. Setting the priority to 255 configures the switch to slave 
mode, and makes it ineligible to become the master. The switch will remain in slave mode even when 
the VLAN fails over from the current master. 

To make effective use of this feature, the normal priority of the ESRP-enabled VLANs must be higher 
than the failover priority of this command.

Example

The following command enables BGP failure tracking, and specifies that the ESRP priority for VLAN 

esrp-1

 be set to 10 when no BGP routes are reachable. 

configure vlan esrp-1 add track-bgp failover 10

History

This command was first available in ExtremeWare 6.2.

Platform Availability

This command is available on 

“i”

 series platforms only.

vlan name

Specifies an ESRP-enabled VLAN name. 

priority

Specifies a number between 0 and 255.

Summary of Contents for ExtremeWare 7.5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExtremeWare 7.5

JETWAY MAGICTWINXP-R10 Software Install Manual preview
MAGICTWINXP-R10
Brand: JETWAY Pages: 43
BrainMaster BMrMMP User Manual preview
BMrMMP
Brand: BrainMaster Pages: 14
Juniper BGP Configuration Manual preview
BGP
Brand: Juniper Pages: 748
Xerox Phaser 340 Installer Installation preview
Phaser 340 Installer
Brand: Xerox Pages: 2
Seagate FreeAgent Desktop 1TB Specifications preview
FreeAgent Desktop 1TB
Brand: Seagate Pages: 2
M-Audio Torq 1.5 User Manual preview
Torq 1.5
Brand: M-Audio Pages: 99
DeLorme XMap 6 User Manual preview
XMap 6
Brand: DeLorme Pages: 437
FieldServer FS-8700-52 Driver Manual preview
FS-8700-52
Brand: FieldServer Pages: 17
Xerox -05W User Manual preview
-05W
Brand: Xerox Pages: 370
FARONICS ANTI-EXECUTABLE STANDARD Manual preview
ANTI-EXECUTABLE STANDARD
Brand: FARONICS Pages: 46
SanDisk SSD ULTRA320 SCSI 3.5" DC-000255 Product Update preview
SSD ULTRA320 SCSI 3.5" DC-000255
Brand: SanDisk Pages: 3
Extreme Networks Ridgeline 3.0 Installation Manual preview
Ridgeline 3.0
Brand: Extreme Networks Pages: 60
Canon Selphy CP510 Printer Software Manual preview
Selphy CP510
Brand: Canon Pages: 28
Jensen GPS navigation software for Audiovox NVX200 User Manual preview
GPS navigation software for Audiovox NVX200
Brand: Jensen Pages: 86
Epson EpsonTalk LP Install Manual preview
EpsonTalk LP
Brand: Epson Pages: 1
Epson EX3200 User Manual preview
EX3200
Brand: Epson Pages: 126
Epson EMP Monitor V4.21 Operation Manual preview
EMP Monitor V4.21
Brand: Epson Pages: 35
Epson EasyMP Monitor 4.53 Operation Manual preview
EasyMP Monitor 4.53
Brand: Epson Pages: 48

Brands by name

Popular brands

Load more brands