Extreme Networks ExtremeWare 7.5 Command Reference Manual Download | Manualshive

Page: 1514 / 2546

background image

1514

ExtremeWare 7.5 Command Reference Guide

ESRP Commands

configure vlan add track-ospf

configure vlan <vlan name> add track-ospf failover <priority>

Description

Configures an ESRP-enabled VLAN to track any available OSPF route.

Syntax Description

Default

No OSPF route tracking.

Usage Guidelines

The switch cannot be the ESRP master if none of the specified routes are reachable.

If no OSPF routes are detected, the ESRP VLAN priority steps to the failover-priority value specified. By
setting the failover priority to be lower than the normal priority of the VLAN, it will cause the affected
VLAN to go into standby.

The range of the priority value is 0 to 254. Setting the priority to 255 configures the switch to slave
mode, and to be ineligible to become the master. The switch will remain in slave mode even when the
VLAN fails over from the current master.

To make effective use of this feature, the normal priority of the ESRP-enabled VLANs must be higher
than the failover priority of this command.

Example

The following command enables OSPF route failure tracking, and specifies that the ESRP priority for
VLAN

esrp-1

be set to 10 when all OSPF routes become unreachable:

configure vlan esrp-1 add track-ospf failover 10

History

This command was first available in ExtremeWare 6.2.

This command was added to the Summit “

e

” series of switches in ExtremeWare 7.3e.

Platform Availability

This command is available on all platforms.

vlan name

Specifies an ESRP-enabled VLAN name.

priority

Specifies a number between 0 and 255.

«
...
1512
1513
1514
1515
1516
...
»

Summary of Contents for ExtremeWare 7.5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExtremeWare 7.5

NETWORK ENTERPRISE - USER 2.2

Brand: Red Hat Pages: 104

Brand: TANDBERG Pages: 10

SpeechExec Dictation Recorder 1.6.0.0

Brand: Philips Pages: 42

Brand: Philips Pages: 56

Brand: Philips Pages: 184

Brand: TC Electronic Pages: 22

Brand: Elgato Pages: 5

Wireless PCI Adapter Driver

Brand: 2Wire Pages: 4

Data Explorer 4 Series

Brand: Applied Biosystems Pages: 447

VB Directory System

Brand: VBrick Systems Pages: 21

StreamPlayer v4.4

Brand: VBrick Systems Pages: 32

Brand: Acroprint Pages: 68

Brand: R&S Pages: 45

Brand: Mad Catz Pages: 16

Database Advanced Security 10g Release 1

Brand: Oracle Pages: 518

DIGITAL XBUS - SOFTWARE

Brand: Mackie Pages: 8

FLASH REMOTING MX-USING FLASH REMOTING FOR FLASH MX 2004 ACTIONSCRIPT...

Brand: MACROMEDIA Pages: 180

ANTI-VIRUS 5.0 - FOR NOVELL NETWARE

Brand: KAPERSKY Pages: 123

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands