Extreme Networks ExtremeWare 7.5 Command Reference Manual Download | Manualshive

Page: 1516 / 2546

background image

1516

ExtremeWare 7.5 Command Reference Guide

ESRP Commands

configure vlan add track-rip

configure vlan <vlan name> add track-rip failover <priority>

Description

Configures an ESRP-enabled VLAN to track any available RIP route.

Syntax Description

Default

No RIP route tracking.

Usage Guidelines

If no RIP routes are detected, the ESRP VLAN priority steps to the failover-priority value specified. By
setting the failover priority to be lower than the normal priority of the VLAN, it will cause the affected
VLAN to go into standby.

The range of the priority value is 0 to 254. Setting the priority to 255 configures the switch to slave
mode, and to be ineligible to become the master. The switch will remain in slave mode even when the
VLAN fails over from the current master.

To make effective use of this feature, the following should be true:

•

The priority field should be given precedence over the other election factors by assigning the

priority-ports-track-mac

election algorithm to the VLAN.

•

The normal priority of the ESRP-enabled VLANs must be higher than the failover priority of this
command.

Example

The following command enables RIP route tracking, and specifies that the ESRP priority for VLAN

esrp-1

be set to 10 upon a diagnostic failure:

configure vlan esrp-1 add track-rip failover 10

History

This command was first available in ExtremeWare 6.2.

This command was added to the Summit “

e

” series of switches in ExtremeWare 7.3e.

Platform Availability

This command is available on all platforms.

vlan name

Specifies an ESRP-enabled VLAN name.

priority

Specifies a number between 0 and 255.

«
...
1514
1515
1516
1517
1518
...
»

Summary of Contents for ExtremeWare 7.5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExtremeWare 7.5

DEEP FREEZE - INTEGRATING WITH NOVELL ZENWORKS...

Brand: FARONICS Pages: 23

Brand: NAPCO Pages: 2

PHOTOSHOP CS 2.0 - SCRIPTING GUIDE

Brand: Adobe Pages: 91

E02D1LL-E - Rational Rose Enterprise

Brand: IBM Pages: 46

Brand: FieldServer Pages: 11

Brand: FieldServer Pages: 19

DREAMWEAVER MX 2004-EXTENDING DREAMWEAVER

Brand: MACROMEDIA Pages: 296

FIREWORKS 8-USING FIREWORKS

Brand: MACROMEDIA Pages: 472

FLEX-FLEX BUILDER

Brand: MACROMEDIA Pages: 56

Powershot S2 IS - Powershot S2 IS 5MP Digital...

Brand: Canon Pages: 137

VS4-ENT-PL-A - vSphere Enterprise Plus

Brand: VMware Pages: 276

1960C - IntelliFAX Color Inkjet

Brand: Brother Pages: 2

Brand: Canon Pages: 104

MOBILE ANTIVIRUS - ANNEXE 480

Brand: ESET Pages: 16

Brand: Vaisala Pages: 19

Brand: Cowon Pages: 10

Brand: ScanSoft Pages: 25

CLX3175FN - COL LASERPR MLTFUNC 4/17PPM...

Brand: Samsung Pages: 26

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands