manualshive.com logo in svg

Extreme Networks ExtremeWare 7.5, Command Reference Manual

Download the free Command Reference Manual for Extreme Networks ExtremeWare 7.5, an advanced networking solution. This comprehensive manual provides detailed instructions and information on utilizing the product's functionalities. Enhance your networking experience by accessing the manual from 88.208.23.73:8080.

Share
Download
background image

 

1554

ExtremeWare 7.5 Command Reference Guide

ESRP Commands

show elrp 

show elrp {<vlan name> | detail} 

Description

Displays ELRP information.

Syntax Description

Default

N/A.

Usage Guidelines

If you enter the 

show elrp

 command without a keyword, the command displays the:

•

Total number of clients registered with ELRP

•

ELRP packets transmitted

•

ELRP packets received 

If you enter the 

detail

 keyword, more detailed status information for VLANs in the master and 

pre-master states is displayed. If you enter a 

vlan name

, the command displays ELRP information for 

that specific VLAN. 

The additional table output for the 

detail

 keyword or a specific VLAN name includes the following:

vlan name

Specifies an ESRP-enabled VLAN name.

detail

Specifies detail for each switch in the ESRP VLAN.

Client name

Displays the name of the ELRP client.

VLAN

Displays the name of the VLAN with ELRP enabled.

Interval

Displays the configured interval. An interval of 3 indicates that ELRP PDUs are transmitted 
every 3 seconds.

Count

Lists the configured number of ELRP PDUs that are transmitted. The PDUs are transmitted at 
the configured interval. This method of ELRP PDU transmission is used by ESRP in the 
pre-master state. A count of 0 indicates continuous PDU transmission. If the Cyclic value is 

Yes

, the count is always 0.

Cyclic

Indicates whether ELRP PDUs are being continuously sent. The column shows 

Yes

 for the 

master VLAN because that VLAN is continuously sending ELRP PDUs for loop detection. 
When a VLAN is in the pre-master state, it only sends three ELRP PDUs before changing to 
master or slave. During this time the column shows 

No

 for that VLAN.

Pkts-Xmit

Displays the number of ELRP PDUs transmitted.

Pkts-Rcvd

Displays the number of ELRP PDUs received.

Summary of Contents for ExtremeWare 7.5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExtremeWare 7.5

IBM NetVista Special Instructions Manual preview
NetVista
Brand: IBM Pages: 34
Campbell PC208 Instruction Manual preview
PC208
Brand: Campbell Pages: 133
M-Audio Heavy Guitars Quick Start Manual preview
Heavy Guitars
Brand: M-Audio Pages: 4
Alarm Lock User Access Control (UAC) in Windows® Vista Tech Note preview
User Access Control (UAC) in Windows® Vista
Brand: Alarm Lock Pages: 2
Red Hat APPLICATION STACK 2.1 RELEASE Release Note preview
APPLICATION STACK 2.1 RELEASE
Brand: Red Hat Pages: 26
ZyXEL Communications Auto Configuration Server Vantage Access Quick Start Manual preview
Auto Configuration Server Vantage Access
Brand: ZyXEL Communications Pages: 113
Vonamic 10059 Configuration Manual preview
10059
Brand: Vonamic Pages: 30
Denon DP-200USB Brochure & Specs preview
DP-200USB
Brand: Denon Pages: 2
Intel Application Accelerator User Manual preview
Application Accelerator
Brand: Intel Pages: 90
Tech Source RAPTOR 2500T-DL - RAPTOR OPENWINDOWS FOR SOLARIS INSTALLATION AND Brochure preview
RAPTOR 2500T-DL - RAPTOR OPENWINDOWS FOR SOLARIS INSTALLATION AND
Brand: Tech Source Pages: 2
SMC Networks ELITEVIEW Management Manual preview
ELITEVIEW
Brand: SMC Networks Pages: 232
Macrovision Corporation SAMREPORT-LITE 2005 Manual preview
SAMREPORT-LITE 2005
Brand: Macrovision Corporation Pages: 44
DataCard Tru Photo Supplementary Manual preview
Tru Photo
Brand: DataCard Pages: 2
Xerox SCAN TO PC DESKTOP 10 Brochure preview
SCAN TO PC DESKTOP 10
Brand: Xerox Pages: 4
NEC Storage Software PathManager User Manual preview
Storage Software PathManager
Brand: NEC Pages: 65
Xerox WorkCentre Pro 232 Driver Manual preview
WorkCentre Pro 232
Brand: Xerox Pages: 64
Cisco CNS NetFlow Collection Engine Installation And Configuration Manual preview
CNS NetFlow Collection Engine
Brand: Cisco Pages: 36
Lenovo ThinkCentre M58e (Portuguese) Manual Do Utilizador preview
ThinkCentre M58e
Brand: Lenovo Pages: 102

Brands by name

Popular brands

Load more brands