manualshive.com logo in svg

Extreme Networks ExtremeWare 7.5, Command Reference Manual

Download the free Command Reference Manual for Extreme Networks ExtremeWare 7.5, an advanced networking solution. This comprehensive manual provides detailed instructions and information on utilizing the product's functionalities. Enhance your networking experience by accessing the manual from 88.208.23.73:8080.

Share
Download
background image

 

configure isis vlan hello-multiplier

ExtremeWare 7.5 Command Reference Guide

1727

configure isis vlan hello-multiplier

configure isis [vlan <vlan name> | all] [level-1| level-2 | level-1-2] 

hello-multiplier <number(3-1000)>

Description

Configures the number of IS-IS Hello packets an IS-IS neighbor at a particular level on this routing 
interface must miss before the it declares that the adjacency with this system is down.

Syntax Description

Default

The default hello multiplier number is 3.

Usage Guidelines

If 

all

 is specified, the hello multiplier is applied to all the routing interfaces in the system. The 

advertised hold time in the IS-IS hellos is the 

hello multiplier

 times the 

hello interval

.

The 

hello multiplier

 range is 3 to 1000, and the default is 3.

The 

level-1

, 

level-2

, and 

level-1-2

 options specify the levels to which the timers are applied.

Example

The following command configures the hello multiplier on level 1 of all VLANs to be 100.

configure isis vlan all level-1 hello-multiplier 100

History

This command was first available in ExtremeWare v6.1.8 IS-IS tech release and subsequently 
incorporated into ExtremeWare 7.0.0.

Platform Availability

This command is available on all platforms.

vlan name

Specifies the name of a VLAN.

all

Specifies all VLANs.

level-1

Specifies IS-IS level 1.

level-2

Specifies IS-IS level 2.

level-1-2

Specifies IS-IS level 1 and level 2.

hello-multiplier

Specifies the hello multiplier.

Summary of Contents for ExtremeWare 7.5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExtremeWare 7.5

Samsung ML-1610 - B/W Laser Printer Manual preview
ML-1610 - B/W Laser Printer
Brand: Samsung Pages: 18
Samsung ML 3471ND - B/W Laser Printer Manual preview
ML 3471ND - B/W Laser Printer
Brand: Samsung Pages: 27
Samsung MFP SCX-6345N User Manual preview
MFP SCX-6345N
Brand: Samsung Pages: 49
Genesys Hosted Provider Edition (HPE) 8.1 Product Availability Announcement preview
Hosted Provider Edition (HPE) 8.1
Brand: Genesys Pages: 5
Red Hat NETWORK BASIC - USER REFERENCE GUIDE 4.0 User Reference Manual preview
NETWORK BASIC - USER REFERENCE GUIDE 4.0
Brand: Red Hat Pages: 92
MACROMEDIA COLDFUSION 5-DEVELOPING Develop Manual preview
COLDFUSION 5-DEVELOPING
Brand: MACROMEDIA Pages: 438
Internet Security Systems RealSecure User Manual preview
RealSecure
Brand: Internet Security Systems Pages: 126
VBrick Systems Portal Server ETV v4.1 Admin Manual preview
Portal Server ETV v4.1
Brand: VBrick Systems Pages: 140
TechSmith Morae 3 Manual preview
Morae 3
Brand: TechSmith Pages: 108
FieldServer FS-8700-54 Driver Manual preview
FS-8700-54
Brand: FieldServer Pages: 8
IBM High Performance Storage System HPSS Installation Manual preview
High Performance Storage System HPSS
Brand: IBM Pages: 311
MACROMEDIA BREEZE PRESENTER Manual preview
BREEZE PRESENTER
Brand: MACROMEDIA Pages: 106
Nokia Symbian S60 v5 User Manual preview
Symbian S60 v5
Brand: Nokia Pages: 6
Nokia Sports Tracker User Manual preview
Sports Tracker
Brand: Nokia Pages: 14
Nokia Transit User Manual preview
Transit
Brand: Nokia Pages: 4
VIP Video Converter User Manual preview
Video Converter
Brand: VIP Pages: 127

Brands by name

Popular brands

Load more brands