manualshive.com logo in svg

Extreme Networks ExtremeWare 7.5, Command Reference Manual

Download the free Command Reference Manual for Extreme Networks ExtremeWare 7.5, an advanced networking solution. This comprehensive manual provides detailed instructions and information on utilizing the product's functionalities. Enhance your networking experience by accessing the manual from 88.208.23.73:8080.

Share
Download
background image

 

configure ospf add vlan area

ExtremeWare 7.5 Command Reference Guide

1733

In either case, LDP must be configured to advertise label mappings for direct routing interfaces.

In some configurations, you may want to enable loopback mode on the VLAN to which the tunnel 
endpoint IP address is assigned. One situation where loopback mode may be useful is when multiple 
physical interfaces, associated with different VLANs, are connected to the MPLS backbone. In this case, 
use of loopback-mode can provide redundancy by enabling TLS traffic to continue even when the 
physical interfaces associated with the tunnel endpoint IP address VLAN fail.

Example

The following command enables OSPF on a VLAN named 

accounting

:

configure ospf add vlan accounting area 0.0.0.1

History

This command was first available in ExtremeWare 2.0. 

This command was modified in an ExtremeWare IP Technology Services Release based on ExtremeWare 
v6.1.8b12 to support MPLS modules.

This command was added to the Summit “

e

” series of switches in ExtremeWare 7.1e. 

This command was modified in an ExtremeWare 7.2e to support the 

all

 keyword.

Platform Availability

This command is available on all platforms.

Summary of Contents for ExtremeWare 7.5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExtremeWare 7.5

M-Audio NRV10 User Manual preview
NRV10
Brand: M-Audio Pages: 32
Symantec GHOST IMAGING FOUNDATION 7.1 Manual preview
GHOST IMAGING FOUNDATION 7.1
Brand: Symantec Pages: 189
KAPERSKY ANTI-VIRUS 5.5 - FOR NOVELL NETWARE Administrator'S Manual preview
ANTI-VIRUS 5.5 - FOR NOVELL NETWARE
Brand: KAPERSKY Pages: 134
MACROMEDIA COLDFUSION 5-ADVANCED ADMINISTRATION Manual preview
COLDFUSION 5-ADVANCED ADMINISTRATION
Brand: MACROMEDIA Pages: 372
Sigma PHOTO PRO 4.2 Manual preview
PHOTO PRO 4.2
Brand: Sigma Pages: 55
Dragon Systems DRAGON NATURALLYSPEAKING PROFESSIONAL 5 Manual preview
DRAGON NATURALLYSPEAKING PROFESSIONAL 5
Brand: Dragon Systems Pages: 222
Novell OPEN WORKGROUP SUITE SMALL BUSINESS EDITION 9.3 - ADMINISTRATION 10-2007 Manual preview
OPEN WORKGROUP SUITE SMALL BUSINESS EDITION 9.3 - ADMINISTRATION 10-2007
Brand: Novell Pages: 30
FARONICS INSIGHT - Manual preview
INSIGHT -
Brand: FARONICS Pages: 43
Red Hat Cluster Suite Manual preview
Cluster Suite
Brand: Red Hat Pages: 188
Applied Biosystems Data Explorer 4 Series User Manual preview
Data Explorer 4 Series
Brand: Applied Biosystems Pages: 447
Zing Magic Checkers User Manual preview
Checkers
Brand: Zing Magic Pages: 10
Labelmaster Masterform 3.0 User Manual preview
Masterform 3.0
Brand: Labelmaster Pages: 81
UNIBLUE SPEEDUPMYPC Quick Start Manual preview
SPEEDUPMYPC
Brand: UNIBLUE Pages: 3
Autodesk 00128-051462-9310 - AUTOCAD 2008 COMM UPG FRM 2005 DVD User Manual preview
00128-051462-9310 - AUTOCAD 2008 COMM UPG FRM 2005 DVD
Brand: Autodesk Pages: 2268
MACROMEDIA COLDFUSION 4.5-DEVELOPING WEB Develop Manual preview
COLDFUSION 4.5-DEVELOPING WEB
Brand: MACROMEDIA Pages: 380
MACROMEDIA DREAMWEAVER 8-DREAMWEAVER API Reference preview
DREAMWEAVER 8-DREAMWEAVER API
Brand: MACROMEDIA Pages: 628
MACROMEDIA FLASH 8-EXTENDING FLASH Manual preview
FLASH 8-EXTENDING FLASH
Brand: MACROMEDIA Pages: 554
GarrettCom Magnum MNS-6K Cli User'S Manual preview
Magnum MNS-6K
Brand: GarrettCom Pages: 329

Brands by name

Popular brands

Load more brands