manualshive.com logo in svg

Extreme Networks ExtremeWare 7.5, Command Reference Manual

Download the free Command Reference Manual for Extreme Networks ExtremeWare 7.5, an advanced networking solution. This comprehensive manual provides detailed instructions and information on utilizing the product's functionalities. Enhance your networking experience by accessing the manual from 88.208.23.73:8080.

Share
Download
background image

 

configure ospf vlan area

ExtremeWare 7.5 Command Reference Guide

1759

configure ospf vlan area

configure ospf [all | vlan <vlan name>] area <area identifier>

Description

Associates a VLAN (router interface) with an OSPF area. By default, all router interfaces are associated 
with area 0.0.0.0.

Syntax Description

Default

Area 0.0.0.0

Usage Guidelines

Any OSPF network that contains more than one area is required to have an area configured as area 0, 
also called the 

backbone

. All areas in an autonomous system must be connected to the backbone. When 

designing networks, you should start with area 0, and then expand into other areas.

The backbone allows summary information to be exchanged between ABRs. Every ABR hears the area 
summaries from all other ABRs. The ABR then forms a picture of the distance to all networks outside of 
its area by examining the collected advertisements, and adding in the backbone distance to each 
advertising router.

When a VLAN is configured to run OSPF, by default you must assign it to an area.

Example

The following command associates the VLAN 

accounting

 with an OSPF area:

configure ospf vlan accounting area 0.0.0.6

History

This command was available in ExtremeWare 2.0.

Platform Availability

This command is available on the 

“i”

 series platforms.

all

Specifies all VLANs.

vlan name

Specifies a VLAN name.

area identifier

Specifies an OSPF area.

Summary of Contents for ExtremeWare 7.5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExtremeWare 7.5

Yamaha M7CL StageMix V1.5 User Manual preview
M7CL StageMix V1.5
Brand: Yamaha Pages: 20
Yamaha LS9-16 Owner'S Manual preview
LS9-16
Brand: Yamaha Pages: 80
Eaton Network Shutdown Module V3 User Manual preview
Network Shutdown Module V3
Brand: Eaton Pages: 65
Arturia JUPITER-8V 2 User Manual preview
JUPITER-8V 2
Brand: Arturia Pages: 125
Juniper JUNOSE 11.2 Configuration Manual preview
JUNOSE 11.2
Brand: Juniper Pages: 772
ICP GDT monitor Manual preview
GDT monitor
Brand: ICP Pages: 60
TRENDnet VIP-L16 - Installation Manual preview
VIP-L16 -
Brand: TRENDnet Pages: 21
Red Hat CERTIFICATE SYSTEM 8 - DEPLOYMENT Install Manual preview
CERTIFICATE SYSTEM 8 - DEPLOYMENT
Brand: Red Hat Pages: 132
Nexo NXtension-ES User Manual preview
NXtension-ES
Brand: Nexo Pages: 24
DeLorme XMap 6 User Manual preview
XMap 6
Brand: DeLorme Pages: 437
GRASS VALLEY Aurora Edit Security Application Note preview
Aurora Edit Security
Brand: GRASS VALLEY Pages: 5
FieldServer FS-8700-80 Driver Manual preview
FS-8700-80
Brand: FieldServer Pages: 43
Bay Networks Manager User Manual preview
Manager
Brand: Bay Networks Pages: 488
MACROMEDIA FLASH 8-DEVELOPING FLASH LITE 2.X Develop Manual preview
FLASH 8-DEVELOPING FLASH LITE 2.X
Brand: MACROMEDIA Pages: 94
IBM TIVOLI SC23-8765-00 User Manual preview
TIVOLI SC23-8765-00
Brand: IBM Pages: 74
KAPERSKY SECURITY 5.5 - FOR MICROSOFT EXCHANGE SERVER... Administrator'S Manual preview
SECURITY 5.5 - FOR MICROSOFT EXCHANGE SERVER...
Brand: KAPERSKY Pages: 185
FARONICS POWER SAVE - REQUIREMENTS GUIDE Manual preview
POWER SAVE - REQUIREMENTS GUIDE
Brand: FARONICS Pages: 17
TC Electronic ASSIMILATOR KONNEKT User Manual preview
ASSIMILATOR KONNEKT
Brand: TC Electronic Pages: 18

Brands by name

Popular brands

Load more brands