enable ospf export direct
ExtremeWare 7.5 Command Reference Guide
1809
enable ospf export direct
enable ospf export direct [cost <metric> [ase-type-1 | ase-type-2] {tag
<number>} | <route map>]
Description
Enables the redistribution of local interface (direct) routes into the OSPF domain. This will not export
the loopback address of 127.0.0.1.
Syntax Description
Default
The default tag number is 0. The default setting is disabled.
Usage Guidelines
After it is enabled, the OSPF router is considered to be an ASBR. Interface routes that correspond to the
interface that has OSPF enabled are ignored.
Exporting routes from OSPF to RIP, and from RIP to OSPF, are discreet configuration functions. To run
OSPF and RIP simultaneously, you must first configure both protocols and then verify the independent
operation of each. Then you can configure the routes to export from OSPF to RIP and the routes to
export from RIP to OSPF.
The cost metric is inserted for all BGP, VIP, RIP-learned, static, and direct routes injected into OSPF. If
the cost metric is set to 0, the cost is inserted from the route. The tag value is used only by special
routing applications. Use 0 if you do not have specific requirements for using a tag. The tag value in
this instance has no relationship with 802.1Q VLAN tagging.
The same cost, type, and tag values can be inserted for all the export routes, or route maps can be used
for selective insertion. When a route map is associated with the export command, the route map is
applied on every exported route. The exported routes can also be filtered using route maps.
Example
The following command enables the distribution of local interface (direct) routes into the OSPF domain:
enable ospf export direct cost 1 ase-type-1 tag 0
metric
Specifies a cost metric.
ase-type-1
Specifies AS-external type 1 routes.
ase-type-2
Specifies AS-external type 2 routes.
number
Specifies a tag value.
route map
Specifies a route map.
Summary of Contents for ExtremeWare 7.5
