manualshive.com logo in svg

Extreme Networks ExtremeWare 7.5, Command Reference Manual

Download the free Command Reference Manual for Extreme Networks ExtremeWare 7.5, an advanced networking solution. This comprehensive manual provides detailed instructions and information on utilizing the product's functionalities. Enhance your networking experience by accessing the manual from 88.208.23.73:8080.

Share
Download
background image

 

configure igmp

ExtremeWare 7.5 Command Reference Guide

1947

configure igmp

configure igmp <query interval> <query response interval> <last member 

query interval>

Description

Configures the Internet Group Management Protocol (IGMP) timers. 

Syntax Description

Default

•

query interval—125 seconds

•

query response interval—10 seconds

•

last member query interval—1 second

Usage Guidelines

Timers are based on RFC2236. Specify the following:

•

query interval—The amount of time, in seconds, the system waits between sending out general 
queries. The range is 1 to 429,496,729 seconds. 

•

query response interval—The maximum response time inserted into the periodic general queries. 
The range is 1 to 25 seconds. 

•

last member query interval—The maximum response time inserted into a group-specific query sent 
in response to a leave group message. The range is 1 to 25 seconds. 

Example

The following command configures the IGMP timers:

configure igmp 100 5 1

History

This command was available in ExtremeWare 2.0.

This command was added to the Summit “

e

” series of switches in ExtremeWare 7.1e.

Platform Availability

This command is available on all platforms.

query interval

Specifies the interval (in seconds) between general queries.

query response interval

Specifies the maximum query response time (in seconds).

last member query interval

Specifies the maximum group-specific query response time (in seconds).

Summary of Contents for ExtremeWare 7.5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExtremeWare 7.5

Canon iR2270 Series Product Description preview
iR2270 Series
Brand: Canon Pages: 2
Canon Pixma Pro9500 Series Manual preview
Pixma Pro9500 Series
Brand: Canon Pages: 31
Canon PowerShot SD430 DIGITAL ELPH WIRELESS Software & Wireless Manual preview
PowerShot SD430 DIGITAL ELPH WIRELESS
Brand: Canon Pages: 130
Canon PowerShot SD880 IS Digital ELPH Software Starter Manual preview
PowerShot SD880 IS Digital ELPH
Brand: Canon Pages: 83
Canon Selphy CP600 Printer Software Manual preview
Selphy CP600
Brand: Canon Pages: 34
Canon N1240U - CanoScan Flatbed Scanner User Manual preview
N1240U - CanoScan Flatbed Scanner
Brand: Canon Pages: 109
XenSource DL385 - ProLiant - G5 Manual preview
DL385 - ProLiant - G5
Brand: XenSource Pages: 313
Xtore XN200 series XN-004-A1 User Manual preview
XN200 series XN-004-A1
Brand: Xtore Pages: 4
Xtore XN200 series XN-004-A1 Software Manual preview
XN200 series XN-004-A1
Brand: Xtore Pages: 7
AMX WebLinx Instruction Manual preview
WebLinx
Brand: AMX Pages: 50
TomTom App for Android Reference Manual preview
App for Android
Brand: TomTom Pages: 58
3Com SUPERSTACK II HUB 10 24-PORT TP User Manual preview
SUPERSTACK II HUB 10 24-PORT TP
Brand: 3Com Pages: 8
3Com 3CWXMUPA Release Note preview
3CWXMUPA
Brand: 3Com Pages: 8
SonicWALL OS 2.x Quick Start Manual preview
OS 2.x
Brand: SonicWALL Pages: 20
Elgato EyeTV Hybrid Hardware Reference Manual preview
EyeTV Hybrid
Brand: Elgato Pages: 5
Adaptec GDTSETUP User Manual preview
GDTSETUP
Brand: Adaptec Pages: 64
Red Hat CERTIFICATE SYSTEM 8 - DEPLOYMENT Install Manual preview
CERTIFICATE SYSTEM 8 - DEPLOYMENT
Brand: Red Hat Pages: 132
Multitech FaxFinder V.34 User Manual preview
FaxFinder V.34
Brand: Multitech Pages: 96

Brands by name

Popular brands

Load more brands