configure flowstats filter ports
ExtremeWare 7.5 Command Reference Guide
2127
configure flowstats filter ports
configure flowstats filter <filter#> {aggregation} {export <group#>} ports
<portlist> [ingress | egress] <filterspec>
Description
Configures a flow record filter for the specified SONET ports.
Syntax Description
Default
By default, filter#1 is configured to
match-all-flows
, and the remaining filters are configured to
match-no-flows
. The
group#
defaults to 1 if the parameter is omitted.
filter#
The
filter#
parameter is an integer in the range from 1 to 8 that operates
with either the
ingress
or
egress
keyword to identify the filter that is being
defined.
aggregation
Reduces the volume of exported data, use this optional keyword to maintain a
single set of statistics for all the flows that match the specified filter.
export <group# tn
Specifies a particular export distribution group on a per-filter basis. Identifies
the set of flow collector devices to which records for flows matching the filter
are to be exported.
portlist
Specifies the port number(s).
ingress
Use this keyword to specify that the filter being defined in the command is one
of the eight filters to be applied to ingress flows.
egress
Use this keyword to specify that the filter being defined in the command is one
of the eight filters to be applied to egress flows.
filterspec
Each filter is defined using a
value
/
filtermask
pair for each of the five
components in the following sequence:
{destination IP address, source IP address,
destination port number, source port number, protocol}
in the form:
[{dest-ip <ipaddress_value/ipaddress_filtermask>}
{source-ip <ipaddress_value/ipaddress_filtermask>}
{dest-port <port_value/port_filtermask>}
{source-port <port_value/port_filtermask>}
{protocol <protocol_value/protocol_filtermask>} |
match-all-flows | match-no-flows]
The
ipaddress_filtermask
,
port_filtermask
, and
protocol_filtermask
parameters are configured using hexadecimal
notation.
You can also use either the
match-all-flows
keyword or the
match-no-flows
keyword in place of settings for the five components. The
match-all-flows
keyword adjusts the
value
/
filtermask
settings for all the
components to 0/0 such that the filter matches any flow. The
match-no-flows
keyword adjusts the
value
/
filtermask
settings for all the
components such that the filter does not match any flow.
Summary of Contents for ExtremeWare 7.5
