Extreme Networks ExtremeWare 7.5 Command Reference Manual Download | Manualshive

Page: 2130 / 2546

background image

2130

ExtremeWare 7.5 Command Reference Guide

PoS Commands—BlackDiamond Switch Only

configure ports tunnel hdlc

configure ports <portlist> tunnel hdlc [off | mpls]

Description

Enables tunneling for HDLC encapsulated frames from a SONET port through an MPLS network.

Syntax Description

Default

The default is

off

.

Usage Guidelines

The ingress SONET port encapsulates the entire HDLC frame (including the HDLC header and FCS)
inside an Ethernet/MPLS header. The egress SONET port strips the Ethernet/MPLS header and
forwards the HDLC frame. HDLC idle bytes (x7E) are not tunneled, but runts and aborted frames are.
HDLC control bytes are destuffed on ingress and stuffed on egress.

When a SONET port is configured for HDLC tunneling, PPP should not be configured on the port (BCP
and IPCP should be off). Furthermore, the port should be the only port in a VLAN and a MPLS
TLS-tunnel should be configured for this VLAN. The payload inside HDLC could be PPP or some other
HDLC-encapsulated protocol. SONET APS (automatic protection switching) is supported between
tunneled PoS ports on the same module or different modules in the same switch. APS for tunneled
ports is not supported for ports on different switches.

Example

The following command example configures an HDLC tunnel, and applies to a PoS module installed in
slot 1 of a BlackDiamond switch:

configure ports 1:4 tunnel hdlc mpls

History

This command was first available in an ExtremeWare IP Technology Services Release based on
v6.1.8b12.

Platform Availability

This command is available on the BlackDiamond switch only.

portlist

Specifies the SONET port number(s).

off

Disables HDLC tunneling.

mpls

Enables an MPLS TLS-tunnel.

«
...
2128
2129
2130
2131
2132
...
»

Summary of Contents for ExtremeWare 7.5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExtremeWare 7.5

Brand: Navitar Pages: 23

CONTRIBUTE 3-CONTRIBUTE PUBLISHING SERVER

Brand: MACROMEDIA Pages: 30

Brand: Nortel Pages: 41

BayStack 380-24F

Brand: Nortel Pages: 76

Brand: Nortel Pages: 176

Express Call Center

Brand: Nortel Pages: 638

Symposium Web Center Portal

Brand: Nortel Pages: 710

Network Video Recorder

Brand: ACTi Pages: 132

Brand: Polycom Pages: 23

DEVICE-MAPPER MULTIPATH 5.2

Brand: Red Hat Pages: 44

CLUSTER SUITE FOR ENTERPRISE LINUX 5.2

Brand: Red Hat Pages: 78

Brand: SAP Pages: 31

Brand: Lowrance Pages: 76

K2-AVID TRANSFER MANAGER

Brand: GRASS VALLEY Pages: 2

One Stop Vocal Processing Plug-in Vocalstrip

Brand: Solid State Logic Pages: 21

ADAPTIVE SERVER IQ 12.4.0

Brand: Sybase Pages: 52

VCLOUD REQUEST MANAGER

Brand: VMware Pages: 2

MEDIASTUDIO PRO 6.0

Brand: Ulead Pages: 360

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands