Extreme Networks ExtremeWare 7.5 Command Reference Manual Download | Manualshive

Page: 2131 / 2546

background image

configure ppp ports

ExtremeWare 7.5 Command Reference Guide

2131

configure ppp ports

configure ppp [bcp [on | off] | ipcp [on {peer-ipaddress <ip address>} |

off]] ports <portlist>

Description

Configures the network control protocol that will run on the specified PPP ports.

Syntax Description

Default

By default, BCP is enabled on all PoS ports. (However, ports 2 and 4 of OC-3c modules are not
members of any VLANs by default; all other ports are members of the default VLAN by default.)

Usage Guidelines

The

bcp

keyword represents the bridging control protocol (BCP), and the

ipcp

keyword represents the

IP control protocol. IPCP and BCP are mutually exclusive configuration options for a given port (that is,
they cannot both be enabled simultaneously on the same port). Generally, when IPCP is enabled on a
port, the port must be a member of one and only one VLAN. Furthermore, no other ports can be
members of this VLAN, and IP routing is the only protocol supported on the VLAN. The one exception
to this rule occurs when SONET automatic protection switching (APS) is enabled. A single VLAN can
contain two IPCP-enabled ports if they are members of the same APS group.

The

peer-ipaddress

keyword provides an option to configure the IP address of the peer router. This

can be useful with peer routers that do not advertise their IP address using the IPCP IP address
configuration option (for example, Juniper routers). If the peer router does advertise an IP address via
IPCP, the configured

peer-ipaddress

is ignored.

BCP enables Ethernet MAC frames to be transported across a PPP link. Thus, any protocol can be
transported across a BCP connection. Essentially, BCP enables the PPP link to appear as an Ethernet
LAN segment to the rest of the switch. Therefore, the port may be a member of multiple VLANs, and
frames can be either bridged or routed onto the link. There are restrictions regarding which ports can be
bridged together (in other words, they may be members of the same VLAN) on the OC-3 PoS Module.
Ports 1 and 2 on the same OC-3 module cannot be bridged together (unless they are members of the
same APS group). Additionally, ports 3 and 4 on the same OC-3 module cannot be bridged together
(unless they are members of the same APS group). There are no similar restrictions regarding bridging
ports together on the OC-12 PoS Module.

PoS operation requires at least one Ethernet I/O module be operational in the chassis. IPCP cannot be
enabled on a port unless BCP is off, and vice versa. IPCP is recommended when a PoS port only carries

bcp

Specifies bridging control protocol for the port.

ipcp

Specifies IP control protocol for the port.

on

Enables the designated protocol on the port.

off

Disables the designated protocol on the port.

peer-ipaddress

Allows you to configure IP address of the peer router.

ip address

Specifies IP address of the peer router.

portlist

Specifies the port number(s).

«
...
2129
2130
2131
2132
2133
...
»

Summary of Contents for ExtremeWare 7.5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExtremeWare 7.5

Brand: Canon Pages: 153

Brand: Canon Pages: 132

Brand: Canon Pages: 135

Brand: Canon Pages: 198

Brand: Canon Pages: 98

Portastudio iPad Application

Brand: Tascam Pages: 5

Brand: Davis Instruments Pages: 108

DIRECTOR MX 2004-USING DIRECTOR

Brand: MACROMEDIA Pages: 500

Blank Media LYT1015

Brand: JVC Pages: 22

Brand: JVC Pages: 43

JLIP VIDEO CAPTURE

Brand: JVC Pages: 56

GR-DVL500U - Digital Camcorder

Brand: JVC Pages: 72

GZMG27US - Everio Camcorder - 680 KP

Brand: JVC Pages: 72

GZ-MG77U - Everio Camcorder - 2.18 MP

Brand: JVC Pages: 72

Digital Photo Navigator ImageMixer with VCD LYT1116-001A

Brand: JVC Pages: 50

GZMG21US - Everio Camcorder - 680 KP

Brand: JVC Pages: 72

Brand: Sony Pages: 1

Walkman D-NE319

Brand: Sony Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands