Extreme Networks ExtremeWare 7.5 Command Reference Manual Download | Manualshive

Page: 2152 / 2546

background image

2152

ExtremeWare 7.5 Command Reference Guide

PoS Commands—BlackDiamond Switch Only

configure sonet trace section ports

configure sonet trace section [<id_byte> | string <id_string>]

ports <portlist>

Description

Configures the section trace identifier for the specified SONET ports.

Syntax Description

Default

The default is 1 for SONET, null for SDH.

Usage Guidelines

Section trace is a maintenance feature of SONET. One byte of the section overhead associated with each
SONET frame is used to carry information identifying the transmitting equipment. The section trace
identifier has two forms: an

id_byte

and an

id_string

. The

id_byte

parameter is an integer in the

range [0-255], with a default value of 1. The

id_string

parameter is a string that may contain up to 15

characters. By default,

id_string

contains 15 NULL characters. The

id_byte

parameter is only

applicable when SONET framing is configured. In this case, the configured

id_byte

value is

transmitted in each SONET frame. Analogously, the

id_string

parameter is only applicable when SDH

framing is configured. SDH framing repetitively cycles through a 15-character string, sending one
character per frame. If the configured string is less than 15 characters, it is padded with NULL
characters.

Example

The following command example sets the section trace identifier to the string

1800wombat

for port 1 of

the PoS module installed in slot 8 of the BlackDiamond switch:

config sonet trace section string 1800wombat ports 8:1

History

This command was first available in an ExtremeWare IP Technology Services Release based on
v6.1.5b20.

Platform Availability

This command is available on the BlackDiamond switch only.

id_byte

Configures the ID byte section trace identifier for the specified SONET port.

id_string

Configures the ID string section trace identifier for the specified SONET port.

portlist

Specifies the port number(s).

«
...
2150
2151
2152
2153
2154
...
»

Summary of Contents for ExtremeWare 7.5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExtremeWare 7.5

Brand: NAPCO Pages: 1

Brand: MAGIX Pages: 88

Brand: Art & Logic Pages: 2

PARTNER ACS PC Administration

Brand: Avaya Pages: 56

Brand: Avaya Pages: 61

Brand: Denon Pages: 2

STRM 2008-2 - TECHNICAL NOTE CHANGING NETWORK SETTING 6-2008

Brand: Juniper Pages: 14

Application Accelerator

Brand: Intel Pages: 90

Brand: Fiery Pages: 214

Trillium Lane Labs

Brand: DigiDesign Pages: 114

18507-051452-9325 - UPG ARCH DESKTOP 2007

Brand: Autodesk Pages: 104

MultiSync P402 DST

Brand: 3M Pages: 57

Android Tablet Software

Brand: PressReader Pages: 4

Brand: IBM Pages: 388

MOVI 4.0 - FOR MAC

Brand: TANDBERG Pages: 19

Brand: Xerox Pages: 4

Brand: Xerox Pages: 32

Brand: Acer Pages: 37

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands