Extreme Networks ExtremeWare 7.5 Command Reference Manual Download

Page: 2238 / 2546

2238

ExtremeWare 7.5 Command Reference Guide

High-Density Gigabit Ethernet Commands—Alpine 3800 and BlackDiamond 6800 Series Only

configure ports egress-rate-limit

configure ports <portlist> egress-rate-limit [percent <percent> | rate

<bps> [k | m]]

Description

Configures a maximum egress rate limit on the specified

“3”

series ports.

Syntax Description

Default

100 percent

Usage Guidelines

If you use the

percent

parameter to configure the egress rate limit, you must use an integer.

The

rate <bps>

range is:

•

kbps—0 to 1000000

•

mbps—0 to 1000

This setting is independent of any

“i”

series egress rate-limiting configurations that you have on the

switch and is applied to the aggregate bandwidth after the

“i”

series per-queue egress rate-limiting.

Example

The following command sets the maximum egress rate limit on slot 1, port 1 to 100 mbps:

configure ports 1:1 egress-rate-limit rate 100 m

History

This command was first available in ExtremeWare 7.1.

Platform Availability

This command is available on

“3”

series I/O modules only.

portlist

Specifies one or more slots and ports. May be in the form 2:*, 2:5, 2:6-2:8.

percent

Specifies the maximum percentage of bandwidth allowed for all egress traffic for each selected port.
The default is 100. The range is 0 to 100.

bps

Specifies the maximum kilobits per second (kbps) or megabits per second (mbps) allowed for all
egress traffic for each selected port.

•

k—kbps (the range is 0-1000000)

•

m—mbps (the range is 0-1000)

«
...
2236
2237
2238
2239
2240
...
»

Summary of Contents for ExtremeWare 7.5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ExtremeWare 7.5

Reviews:

Related manuals for ExtremeWare 7.5

Brands by name

Popular brands

Extreme Networks ExtremeWare 7.5, Command Reference Manual

Search results

Summary of Contents for ExtremeWare 7.5

Reviews:

Related manuals for ExtremeWare 7.5

Brands by name

Popular brands