Extreme Networks ExtremeWare 7.5 Command Reference Manual Download | Manualshive

Page: 2382 / 2546

background image

2382

ExtremeWare 7.5 Command Reference Guide

H-VPLS Commands—BlackDiamond Switch Only

configure mpls vpls add

configure mpls vpls <vpls_name> add [vlan <vlan_name> | ports <port-list>]

Description

Configures service for VPLS.

Syntax Description

Default

N/A.

Usage Guidelines

This command configures a local Ethernet VPLS interface for the specified

vpls_name

. The VPLS

interface may be a VLAN or a physical port. Specifying the

vlan_name

logically binds the VLAN to the

specified vpls. Only one VLAN may be configured per VPLS. Specifying a port-list logically binds one
or more physical ports to the specified vpls. Only ports configured for

edge-service-mode

port can be

directly added to a vpls (see Configure MPLS Edge Service Mode on page 3 for additional information).

Edge-service-mode

vlan ports must be added to a VLAN and the VLAN assigned to a vpls, since the

VLAN ID (and not the port) is the service identifier. If multiple ports are added or there are multiple
ports configured for vlan_name, VPLS traffic local to the switch is forwarded within the switch.
Simultaneous support for both vlan and ports for a single vpls is not supported.

When a vlan interface has been configured for a VPLS, the VLAN is added to the VPLS as specified by
the v

pls_name

. The VLAN ID is locally significant to each VPLS. Thus, each VLAN VPLS interface

within the H-VPLS network, may have a different VLAN ID. This greatly simplifies VLAN ID
coordination between metro network access points. Traffic may be switched locally between VLAN
ports if more than one port is configured for the VLAN.

When a port interface has been configured for a VPLS, the port-list is automatically added to a unique
VMAN ID. The VMAN ID assigned, is the highest unallocated VLAN ID. The VMAN allocated for the
VLAN ID has the same name as the configured VPLS instance (i.e.,

vpls_name

). Any additional local

switch ports added to the VPLS are implicitly added to the VMAN. The VMAN ID uniquely maps to a

vpls_name

and thus identifies the ports that have been added to the Port VPLS interface. Because the

VMAN ID must uniquely identify the port, the port cannot be added to any other local VLAN.

Example

config mpls vpls myvpls add [vlan <vlan_name> | ports <port-list>]

config mpls vpls myvpls add myvlan

config mpls vpls myvpls add ports 1:5

History

This command was first available in an ExtremeWare 7.3.0.

vpls_name

Identifies the VPLS interface within the switch (character string)

vlan_name

Logically binds the VLAN to the specified vpls.

port-list

Specifies a list of ports.

«
...
2380
2381
2382
2383
2384
...
»

Summary of Contents for ExtremeWare 7.5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExtremeWare 7.5

Brand: Canon Pages: 2

Pixma Pro9500 Series

Brand: Canon Pages: 31

PowerShot SD430 DIGITAL ELPH WIRELESS

Brand: Canon Pages: 130

PowerShot SD880 IS Digital ELPH

Brand: Canon Pages: 83

Brand: Canon Pages: 34

N1240U - CanoScan Flatbed Scanner

Brand: Canon Pages: 109

Brand: On-Q/Legrand Pages: 14

ZENworks 7.2 Linux Management

Brand: Novell Pages: 10

BMP5 Direct SDK

Brand: Campbell Pages: 32

CONTRIBUTE-USING CONTRIBUTE

Brand: MACROMEDIA Pages: 214

AMD-8151 HyperTransport AGP3.0

Brand: AMD Pages: 16

ThinkCentre A58

Brand: Lenovo Pages: 2

Brand: RGB Spectrum Pages: 158

Portal Server ETV v4.1

Brand: VBrick Systems Pages: 140

Brand: AMX Pages: 24

Brand: Cyber Sciences Pages: 2

Brand: MINOLTA-QMS Pages: 42

Brand: Qlogic Pages: 284

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands