2388
ExtremeWare 7.5 Command Reference Guide
H-VPLS Commands—BlackDiamond Switch Only
configure mpls health-check add mplsping
configure mpls health-check add mplsping [<ipaddress> | prefix
<ipaddress/masklength> | <host_name> | lsp <lsp_name>]{interval-time
<seconds>} {trap-send-holdtime <seconds>}
Description
Configures an MPLS tunnel LSP service connectivity health-check.
Syntax Description
Default
interval-time range - 60 seconds
trap-send-holdtime range - 10 seconds
Usage Guidelines
This command configures a MPLS tunnel LSP service connectivity health-check. The health-check
command can be used to configure recurring tunnel LSP connectivity checks. If the configured tunnel
LSP connectivity is lost, a trap is sent to alert management stations of a possible service failure and an
error message is logged. Connectivity is verified by sending an MPLS ping packet. Up to 256 mplsping
health-checks can be configured.
Ping packets are sent at the rate specified by the
interval-time.
If an echo response is not received
within
trap-send-holdtime
seconds after the
interval-time
ping was sent, service connectivity is
considered down and an error message is logged and a trap message may be sent. The valid
interval-time
range is 10 to 600 seconds with a default value of 60 seconds. The valid
trap-send-holdtime
range is 3 to 30 seconds with a default value of 10 seconds and must be less that
the
interval-time
. Ping packets may be dropped due to spurious network conditions. In order to
minimize service disconnect “false alerts”, when an echo request has not been received within
trap-send-holdtime
/3 seconds, echo requests are sent in rapid succession at a rate of one per second.
This operation continues until an echo response is received or the trap-send-holdtime expires. If an echo
response is received before the
trap-send-holdtime
expires, the rapid sending of echo requests is
immediately stopped and the service is deemed connected.
Specifying the LSP FEC configures the tunnel LSP health-check. The FEC can be specified using the
ipaddress
,
ipaddress/masklength
or
host_name
parameter. If the FEC is specified using the
host_name parameter, the DNS client must be configured so that the host_name can first be resolved to
an IP address. The resolved host name IP address is assumed to be a /32 prefix. If there is more than
one outgoing LSP that matches the FEC, only one is used. For RSVP-TE LSPs, the FEC is implied from
the LSP configuration. Thus, the
lsp
keyword may be used to configure an tunnel LSP health-check for
lsp_name
.
ipaddress
Option for specifying the forwarding equivalence class (FEC).
ipaddress/masklength
Option for specifying the FEC.
host_name
Option for specifying the FEC. Must be able to be resolved to an IP address.
lsp_name
Configures the tunnel LSP health-check
interval-time
Determines the rate at which ping packets are sent.
trap-send-holdtime
Specifies the interval after interval-time when service connectivity is
considered down if there is no echo response.
Summary of Contents for ExtremeWare 7.5
