Extreme Networks ExtremeWare 7.5 Command Reference Manual Download | Manualshive

Page: 2419 / 2546

background image

vplsping

ExtremeWare 7.5 Command Reference Guide

2419

bytes in hex format. The specified or learned MAC address is copied into the destination MAC address
field of the VPLS echo request and is included in the L2-VPN Prefix Target FEC TLV. By default, the
switch's MAC address is used for the source MAC address of the VPLS echo request. The

from

keyword

optionally specifies the source MAC address used for the VPLS echo request. This option allows the
VPLS echo request to be sent as if it originated from a customer's source MAC address. If link
aggregation is supported along the path to the destination MAC address, this insures that the VPLS
ping verifies connectivity through the VPLS network for the exact same path that the customer's traffic
would travel.

The optional

continuous

keyword specifies that VPLS ping packets be sent continuously. The operation

can be interrupted by pressing any key.

The optional size keyword specifies the number of bytes to include as payload data in the VPLS ping
packet. If no

start_size

parameter is specified, the size of the payload data is eight bytes. The

minimum valid

start_size

value is one. The maximum

start_size

value is variable, depending on

the type of VPLS ping packet sent, but the total size of the VPLS ping packet cannot exceed the
configured jumbo packet size, if jumbo frames are enabled, or 1518 if jumbo frames are disabled. If the

end_size

parameter is specified, the size of the packet will increment by one byte for each new VPLS

echo request sent. The next VPLS echo request is not sent until the VPLS echo response for the previous
packet is received. This is useful for detecting interface MTU mismatch configurations between VPLS
nodes. The node ceases sending VPLS echo requests when the specified

end_size

value is reached, the

VPLS ping is interrupted, or a VPLS echo response is not received after four successive retries.

The optional

reply-mode

keyword is used to specify the return path for the VPLS echo response. When

the ip option is specified, the VPLS echo reply is routed back to the sender, specified in the L2 VPN
Prefix sub-TLV, via an IPv4 packet with the IP Router Alert option. If the

mpls

option is specified, the

VPLS echo reply is routed back to the sender over an MPLS LSP. If no LSP is available, the VPLS echo
reply is not sent. When the

vpls

option is specified, the VPLS echo reply is switched in-band back to

the sender via a VPLS encapsulated IPv4 packet. This option is useful for determining if there is a
failure along the return VPLS VC-LSP path. If the

reply-mode

is not specified, the vpls reply mode is

used.

Example

None

History

This command was first available in an ExtremeWare 7.3.0.

Platform Availability

This command is available on the BlackDiamond switch only.

«
...
2417
2418
2419
2420
2421
...
»

Summary of Contents for ExtremeWare 7.5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExtremeWare 7.5

Brand: Canon Pages: 2

Pixma Pro9500 Series

Brand: Canon Pages: 31

PowerShot SD430 DIGITAL ELPH WIRELESS

Brand: Canon Pages: 130

PowerShot SD880 IS Digital ELPH

Brand: Canon Pages: 83

Brand: Canon Pages: 34

N1240U - CanoScan Flatbed Scanner

Brand: Canon Pages: 109

Jetstream CPX-1000

Brand: Paradyne Pages: 93

ANTI-EXECUTABLE ENTERPRISE

Brand: FARONICS Pages: 68

Brand: Avaya Pages: 216

Brand: MACROMEDIA Pages: 830

Brand: Apricorn Pages: 20

Brand: Apricorn Pages: 67

Brand: Avaya Pages: 48

NORTON INTERNET SECURITY - FOR MAC V4

Brand: Symantec Pages: 28

CONFLICTMANAGER

Brand: Symantec Pages: 54

DIRECTOR MX-LINGO DICTIONARY

Brand: MACROMEDIA Pages: 756

Linear-Phase MultiBand Software Audio...

Brand: Waves Pages: 27

CAMEDIA Master 4.3/Pro

Brand: Olympus Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands