manualshive.com logo in svg

Extreme Networks ExtremeWare 7.5, Command Reference Manual

Download the free Command Reference Manual for Extreme Networks ExtremeWare 7.5, an advanced networking solution. This comprehensive manual provides detailed instructions and information on utilizing the product's functionalities. Enhance your networking experience by accessing the manual from 88.208.23.73:8080.

Share
Download
background image

 

show mpls rsvp-te lsp

ExtremeWare 7.5 Command Reference Guide

2515

show mpls rsvp-te lsp

show mpls rsvp-te lsp {<lsp_name>} {detail}

Description

Displays the RSVP-TE LSP.

Syntax Description

Default

N/A.

Usage Guidelines

This command displays the configuration and status information for RSVP-TE LSPs. Information is 
listed in tabular format and includes the LSP name, LSP state, active path name, bandwidth requested, 
bandwidth actually reserved, ERO flag, egress LSR, LSP up-time, and RSVP error codes (if LSP setup 
failed). If you specify a specific LSP name, only information for the specified LSP is displayed. If you 
specify the optional 

detail

 keyword, additional information is displayed for each LSP. The detailed 

information includes a list of all configured paths, including the path state, error codes for the LSP 
associated with each path, up-time for each LSP, the bound profile name, and a list of TLS tunnels 
configured to use the LSP.

Example

The following displays the configuration and status information for all configured RSVP-TE LSPs in 
detailed format:

show mpls rsvp-te lsp detail

History

This command was first available in an ExtremeWare IP Technology Services Release based on 
v6.1.8b12.

This command was subsequently incorporated into ExtremeWare 7.0.0.

Platform Availability

This command is available on the BlackDiamond switch only.

lsp_name

Specifies the name of the LSP.

detail

Specifies to display the information in detailed format.

Summary of Contents for ExtremeWare 7.5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExtremeWare 7.5

F-SECURE PSB Getting Started Manual preview
PSB
Brand: F-SECURE Pages: 18
Xerox DocuPrint N4025 User Manual preview
DocuPrint N4025
Brand: Xerox Pages: 129
Mitsubishi WiFi-Doc Client for iOS User Manual preview
WiFi-Doc Client for iOS
Brand: Mitsubishi Pages: 10
Internet Security Systems RealSecure User Manual preview
RealSecure
Brand: Internet Security Systems Pages: 126
Arturia Prophet V User Manual preview
Prophet V
Brand: Arturia Pages: 117
Red Hat CLUSTER SUITE FOR ENTERPRISE LINUX 4.5 Installation Manual preview
CLUSTER SUITE FOR ENTERPRISE LINUX 4.5
Brand: Red Hat Pages: 110
3Com 3CR15600 - Enterprise Management Suite Getting Started Manual preview
3CR15600 - Enterprise Management Suite
Brand: 3Com Pages: 218
Intel IT DIRECTOR Manual preview
IT DIRECTOR
Brand: Intel Pages: 43
AMX AXD-CV6 Instruction Manual preview
AXD-CV6
Brand: AMX Pages: 54
GRASS VALLEY Aurora Edit Security Application Note preview
Aurora Edit Security
Brand: GRASS VALLEY Pages: 5
GRASS VALLEY MEDIAEDGE-SVS4 Datasheet preview
MEDIAEDGE-SVS4
Brand: GRASS VALLEY Pages: 2
GRASS VALLEY EDIUS 6 Application Note preview
EDIUS 6
Brand: GRASS VALLEY Pages: 24
GRASS VALLEY AURORA INGEST - S AND UPGRADE INSTRUCTIONS V7.1 Upgrade Instructions preview
AURORA INGEST - S AND UPGRADE INSTRUCTIONS V7.1
Brand: GRASS VALLEY Pages: 66
GRASS VALLEY AURORA BROWSE 7 Datasheet preview
AURORA BROWSE 7
Brand: GRASS VALLEY Pages: 4
GRASS VALLEY EDIUS NEO 3 Datasheet preview
EDIUS NEO 3
Brand: GRASS VALLEY Pages: 2
UNIBLUE RegistryBooster 2010 Product Manual preview
RegistryBooster 2010
Brand: UNIBLUE Pages: 11
Lucid Virtu Installation Manual preview
Virtu
Brand: Lucid Pages: 10
Lucid FM2A85X Extreme4 Installation Manual preview
FM2A85X Extreme4
Brand: Lucid Pages: 12

Brands by name

Popular brands

Load more brands