manualshive.com logo in svg

Extreme Networks ExtremeWare 7.5, Command Reference Manual

Download the free Command Reference Manual for Extreme Networks ExtremeWare 7.5, an advanced networking solution. This comprehensive manual provides detailed instructions and information on utilizing the product's functionalities. Enhance your networking experience by accessing the manual from 88.208.23.73:8080.

Share
Download
background image

 

enable slot

ExtremeWare 7.5 Command Reference Guide

315

enable slot

enable slot [all | msm-a | msm-b | <slot number>] 

Description

Enables one or all slots on a BlackDiamond or Alpine switch. 

Syntax Description

Default

Enabled

Usage Guidelines

This command allows the user to enable a slot that has been previously disabled using the 

disable 

slot

 command. 

When you enter the enable command, the disabled I/O module in the specified slot is brought up, and 
the slot is made operational, if possible, or goes to the appropriate state as determined by the card state 
machine. The LEDs on the module are brought ON as usual. You can either enable a slot individually, 
or use the 

enable slot all

 command to enable all the slots. 

After you enable the slot, the 

show slot

 command shows the state as “Operational” or will display the 

appropriate state if the module could not be brought up successfully. Note that there is no card state 
named “Enable” and the module goes to the appropriate states as determined by the card state machine 
when the 

enable slot

 command is invoked. 

Only slots that have their state as “disabled” can be enabled using this command. If this command is 
used on slots that are in states other than “disabled,” the card state machine takes no action on these 
slots. 

Example

The following command enables slot 5 on the switch:

enable slot 5

History

This command was first available in ExtremeWare 6.2.1.

Platform Availability

This command is available on BlackDiamond and Alpine switches only.

all

Species that all slots in the device should be enables. 

msm-a

Specifies that MSM-A should be enabled.

msm-b

Specifies that MSM-B should be enabled.

slot number

Specifies the slot to be enabled. 

Summary of Contents for ExtremeWare 7.5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExtremeWare 7.5

DAVIS and Vantage Pro Getting Started Manual preview
and Vantage Pro
Brand: DAVIS Pages: 16
Adobe 718659340025 - InDesign CS - PC Printing Manual preview
718659340025 - InDesign CS - PC
Brand: Adobe Pages: 122
altiris eXpress Altris eXpress Helpdesk Solution 5.6 SP1 User Manual preview
eXpress Altris eXpress Helpdesk Solution 5.6 SP1
Brand: altiris Pages: 143
Amazon Appointment Request Portal User Manual preview
Appointment Request Portal
Brand: Amazon Pages: 16
Barracuda Networks NG Network Access Client SP4 Migration Instructions preview
NG Network Access Client SP4
Brand: Barracuda Networks Pages: 10
AMX I!-FTPSENDER Instruction Manual preview
I!-FTPSENDER
Brand: AMX Pages: 12
ALK CoPilot CoPilot Live Smartphone User Manual preview
CoPilot CoPilot Live Smartphone
Brand: ALK Pages: 42
Ricoh Web SmartDeviceMonitor Standard Manual preview
Web SmartDeviceMonitor Standard
Brand: Ricoh Pages: 1
BT Voyager Digital Media Player Installation & User Manual preview
Voyager Digital Media Player
Brand: BT Pages: 30
VBrick Systems Portal Server ETV v4.2 User Manual preview
Portal Server ETV v4.2
Brand: VBrick Systems Pages: 64
Texas Instruments Derive 5 Introduction Manual preview
Derive 5
Brand: Texas Instruments Pages: 58
Texas Instruments LearningCheck Creator Reference Manual preview
LearningCheck Creator
Brand: Texas Instruments Pages: 81
GNOME 2.4 User Manual preview
2.4
Brand: GNOME Pages: 213
Bay Networks NA User Manual preview
NA
Brand: Bay Networks Pages: 88
Yamaha VE Owner'S Manual preview
VE
Brand: Yamaha Pages: 33
Zennio Z41 User Manual preview
Z41
Brand: Zennio Pages: 15
Jensen NVX200 - Touch&Go - Automotive GPS Receiver User Manual preview
NVX200 - Touch&Go - Automotive GPS Receiver
Brand: Jensen Pages: 86
Acer RDM User Manual preview
RDM
Brand: Acer Pages: 4

Brands by name

Popular brands

Load more brands