manualshive.com logo in svg

Extreme Networks ExtremeWare 7.5, Command Reference Manual

Download the free Command Reference Manual for Extreme Networks ExtremeWare 7.5, an advanced networking solution. This comprehensive manual provides detailed instructions and information on utilizing the product's functionalities. Enhance your networking experience by accessing the manual from 88.208.23.73:8080.

Share
Download
background image

 

configure gvrp port

ExtremeWare 7.5 Command Reference Guide

361

configure gvrp port

configure gvrp {listen | send | both | none} port <portlist> 

Description

Configures the sending and receiving of Generic VLAN Registration Protocol (GVRP) information on a 
port.

NOTE

This command is available only on “i” series switches running ExtremeWare version 6.0 or earlier.

Syntax Description

 

Default

Both sending and receiving.

Usage Guidelines

GVRP must be enabled on the switch as a whole before GVRP data can be sent or received on 
individual ports. 

If GVRP is enabled, 

send

 causes information (GVRP packets) about tagged VLANS on the switch to be 

sent on the specified ports, to neighboring GVRP-enabled switches.

If GVRP is enabled, 

listen

 means that the switch will receive and act on GVRP information it receives 

on the specified ports, from neighboring GVRP-enabled switches. 

Example

The following commands configure port 3 to receive GVRP information only (by default it can send and 
listen) and then enables GVRP:

configure gvrp listen port 3

enable gvrp

If the switch receives GVRP information on this port, it will do one of the following:

•

If a tagged VLAN already exists with a VLANid that matches the VLANid in the GVRP data, and 
port 3 is not already a member of that VLAN, add it as a tagged port.

•

If no VLAN exists with a VLANid that matches the VLANid in the GVRP data, create a VLAN with 
the VLANid specified in the GVRP data, and add port 3 as a tagged member port. 

listen

Enables the receipt of GVRP packets on the specified port(s).

send

Enables sending of GVRP packets on the specified port(s).

both

Enables both sending and receiving of GVRP packets.

none

Disables the port from participating in GVRP operation.

portlist

Specifies one or more ports. May be in the form 1, 2, 3-5, 2:5, 2:6-2:8.

Summary of Contents for ExtremeWare 7.5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExtremeWare 7.5

Canon 70 MC - ZR70MC MiniDV Digital Camcorder Instruction Manual preview
70 MC - ZR70MC MiniDV Digital Camcorder
Brand: Canon Pages: 57
Yellowtec b-line Manual preview
b-line
Brand: Yellowtec Pages: 124
Euphonix MixView 3.0 Overview preview
MixView 3.0
Brand: Euphonix Pages: 8
Fargo Persona Persona M30e User Manual preview
Persona Persona M30e
Brand: Fargo Pages: 31
Sanyo VA-SW8000 Instruction Manual preview
VA-SW8000
Brand: Sanyo Pages: 132
Genius HyperMedia Center Manual preview
HyperMedia Center
Brand: Genius Pages: 12
John Bowen Solaris V5 User Manual preview
Solaris V5
Brand: John Bowen Pages: 47
ION MixMeister EZ Setup & Troubleshooting preview
MixMeister EZ
Brand: ION Pages: 12
TechSmith Morae 3 Manual preview
Morae 3
Brand: TechSmith Pages: 108
Labelmaster Masterform 3.0 User Manual preview
Masterform 3.0
Brand: Labelmaster Pages: 81
Nikon DI series Manual (Install To Pc) preview
DI series
Brand: Nikon Pages: 12
Nikon Nikon View Software Manual preview
Nikon View
Brand: Nikon Pages: 12
UNIBLUE DRIVERSCANNER Quick Start Manual preview
DRIVERSCANNER
Brand: UNIBLUE Pages: 3
FieldServer FS-8700-73 Driver Manual preview
FS-8700-73
Brand: FieldServer Pages: 48
MACROMEDIA FLASHLITE2 ACTIONSCRIPT-LANGUAGE Reference preview
FLASHLITE2 ACTIONSCRIPT-LANGUAGE
Brand: MACROMEDIA Pages: 780
KapLogic Aegis2.2x Installation Manual preview
Aegis2.2x
Brand: KapLogic Pages: 24
KAPERSKY ANTI-VIRUS 6.0 User Manual preview
ANTI-VIRUS 6.0
Brand: KAPERSKY Pages: 298
Waves Abbey Road RS56 User Manual preview
Abbey Road RS56
Brand: Waves Pages: 13

Brands by name

Popular brands

Load more brands