manualshive.com logo in svg

Extreme Networks ExtremeWare 7.5, Command Reference Manual

Download the free Command Reference Manual for Extreme Networks ExtremeWare 7.5, an advanced networking solution. This comprehensive manual provides detailed instructions and information on utilizing the product's functionalities. Enhance your networking experience by accessing the manual from 88.208.23.73:8080.

Share
Download
background image

 

414

ExtremeWare 7.5 Command Reference Guide

FDB Commands

•

A port is disabled.

•

A port enters blocking state.

•

A port QoS setting is changed.

•

A port goes down (link down).

Using the 

any-mac

 keyword, you can enable traffic from a QoS VLAN to have higher priority than 

802.1p traffic. Normally, an 802.1p packet has a higher priority over the VLAN classification. To use this 
feature, you must create a wildcard permanent FDB entry named 

any-mac

 and apply the QoS profile to 

the individual MAC entry.

You can use the 

show fdb

 permanent

 command to display permanent FDB entries, including their QoS 

profile associations. 

On the 

“i”

 Series of Switches.  

If you specify only the ingress QoS profile, the egress QoS profile 

defaults to none, and vice-versa. If both profiles are specified, the source MAC address of an ingress 
packet and the destination MAC address of an egress packet are examined for QoS profile assignment.

Example

The following example associates the QoS profile qp2 with a dynamic entry for MAC address 
00:A0:23:12:34:56 on VLAN net34 that will be learned by the FDB:

create fdbentry 00:A0:23:12:34:56 vlan net34 dynamic qosprofile qp2

QoS profile 

qp2

 will be applied when the entry is learned.

The following example associates the QoS profile qp5 with the wildcard permanent FDB entry any-mac 
on VLAN v110:

create fdbentry any-mac vlan v110 dynamic ingress-qosprofile qp5

History

This command was available in ExtremeWare 2.0. 

Support for associating separate QoS profiles with ingress and egress ports was added in ExtremeWare 
6.2.

This command was modified in ExtremeWare 6.2.1 to support the 

broadcast-mac

 option. 

This command was added to the Summit “

e

” series of switches in ExtremeWare 7.1e. 

This command was modified in ExtremeWare 7.2e to support the 

any-mac

 option. 

Platform Availability

This command is available on all platforms.

Summary of Contents for ExtremeWare 7.5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExtremeWare 7.5

Altigen Altiware HPBX 5.0A Administration Manual preview
Altiware HPBX 5.0A
Brand: Altigen Pages: 490
Barracuda Networks NG Network Access Client SP4 Migration Instructions preview
NG Network Access Client SP4
Brand: Barracuda Networks Pages: 10
AMX I!-FTPSENDER Instruction Manual preview
I!-FTPSENDER
Brand: AMX Pages: 12
KAPERSKY ANTI-VIRUS 5.5 - FOR NOVELL NETWARE Administrator'S Manual preview
ANTI-VIRUS 5.5 - FOR NOVELL NETWARE
Brand: KAPERSKY Pages: 134
TANDBERG Movi 3.0 User Manual preview
Movi 3.0
Brand: TANDBERG Pages: 10
SanDisk musicmatch User Manual preview
musicmatch
Brand: SanDisk Pages: 11
Qlogic SANbox-8 User Manual preview
SANbox-8
Brand: Qlogic Pages: 180
Fujitsu Saving and Recovering Your Factory and System Images Manual preview
Saving and Recovering Your Factory and System Images
Brand: Fujitsu Pages: 16
Fujitsu Solaris 10 Hardware Platform Manual preview
Solaris 10
Brand: Fujitsu Pages: 52
Fujitsu Restoring Microsoft Windows® 7 Edition Manual preview
Restoring Microsoft Windows® 7 Edition
Brand: Fujitsu Pages: 4
Fujitsu ServerView Event Manager User Manual preview
ServerView Event Manager
Brand: Fujitsu Pages: 172
Fujitsu ScandAll PRO How To Use Manual preview
ScandAll PRO
Brand: Fujitsu Pages: 45
Fujitsu SOFTUNE User Manual preview
SOFTUNE
Brand: Fujitsu Pages: 234
Fujitsu ServerView Operations Manager V6.12 User Manual preview
ServerView Operations Manager V6.12
Brand: Fujitsu Pages: 282
Fujitsu ServerView Virtual-IO Manager V3.1 User Manual preview
ServerView Virtual-IO Manager V3.1
Brand: Fujitsu Pages: 362
Fujitsu ServerView Resource Orchestrator Cloud Edition V3.1.1 Operation User Manual preview
ServerView Resource Orchestrator Cloud Edition V3.1.1 Operation
Brand: Fujitsu Pages: 414
Fujitsu Remote Management User Manual preview
Remote Management
Brand: Fujitsu Pages: 426
Nortel SCS User Manual preview
SCS
Brand: Nortel Pages: 41

Brands by name

Popular brands

Load more brands