Extreme Networks ExtremeWare 7.5 Command Reference Manual Download

Page: 424 / 2546

424

ExtremeWare 7.5 Command Reference Guide

FDB Commands

show fdb

“i”

series of switches:

show fdb {<mac_address> | broadcast-mac | permanent | ports <portlist> |

remap | vlan <vlan name>}

“e”

series of switches:

show fdb {<mac_address> | permanent | ports <portlist> | vlan <vlan name>}

Description

Displays FDB entries.

Syntax Description

Default

All

Usage Guidelines

Displays FDB entries as specified, or displays all FDB entries.

The show output displays the following information:

mac_address

Specifies a MAC address, using colon-separated bytes, for which FDB entries should be
displayed.

broadcast-mac

Specifies the broadcast MAC address. May be used as an alternate to the colon-separated
byte form of the address ff:ff:ff:ff:ff:ff.

NOTE: This option is only available on the

“i”

series of switches.

permanent

Displays all permanent entries, including the ingress and egress QoS profiles and secure MAC
addresses.

portlist

Displays the entries for one or more ports. May be in the form 1, 2, 3-5, 2:5, 2:6-2:8.

remap

Displays the remapped FDB entries.

NOTE: This option is only available on the

“i”

series of switches.

vlan name

Displays the entries for a specific VLAN.

EQP

The Ingress QoS profile assigned to the entry (appears only if the keyword permanent is specified).

IQP

The Egress QoS profile assigned to the entry (appears only if the keyword permanent is specified).

Index

The FDB hash index, in the format <bucket>-<entry>.

Mac

The MAC address that defines the entry.

Vlan

The VLAN for the entry.

Age

The age of the entry, in seconds (does not appear if the keyword permanent is specified).

Use

The number of IP FDB entries that use this MAC address as a next hop or last hop (does not appear
if the keyword permanent is specified).

Summary of Contents for ExtremeWare 7.5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for ExtremeWare 7.5

Reviews:

Related manuals for ExtremeWare 7.5

Brands by name

Popular brands

Extreme Networks ExtremeWare 7.5, Command Reference Manual

Search results

Summary of Contents for ExtremeWare 7.5

Reviews:

Related manuals for ExtremeWare 7.5

Brands by name

Popular brands