Extreme Networks ExtremeWare 7.5 Command Reference Manual Download | Manualshive

Page: 708 / 2546

background image

708

ExtremeWare 7.5 Command Reference Guide

Commands for Status Monitoring and Statistics

configure sys-health-check auto-recovery

configure sys-health-check auto-recovery <number> [offline | online]

Description

Configures the auto-recovery function of the system health checker.

NOTE

This command is available only on the “i” series switches.

Syntax Description

Default

The default alarm level is log.

Usage Guidelines

This command allows you to configure the switch’s reaction to a failed health check.

The system health checker tests I/O modules, MSM modules, and the backplane by forwarding packets
every 4 seconds. Additional checking for the validity of these packets is completed by performing a
checksum.

By isolating faults to a specific module, MSM, or backplane connection, the system health checker
prevents corrupted packets from being propagated to the CPU, upper layer modules, or the rest of your
network. If you observe a failure, please contact Extreme Technical Support.

Depending on how you have configured the system health checker, failed system health checks can
generate critical error messages in the syslog, and can also send a trap and/or shut down the system.
The system health checker continues to periodically forward test packets to failed components. If
auto-recovery is configured, the system attempts to automatically reset the faulty module and bring it
back on line.

In ExtremeWare versions prior to 6.2, you cannot use both mirroring and the system health checker at
the same time. If you configure mirroring with the system health checker enabled, the health checker
indicates that it has been disabled by sending a message to the syslog. In ExtremeWare 6.2 or later, this
restriction does not apply.

number

Specifies the number of times that the health checker attempts to auto-recover a faulty module.
The range is from 0 through 255 times. Default is 3 times.

NOTE: This option is available only in BlackDiamond I/O modules.

offline

Specifies that a faulty module is taken offline and kept offline if one of the following occurs:

•

More than eight defects are detected.

•

Three consecutive checksum errors were detected by the health checker, but no new defects
were found by the memory scanning and mapping process.

•

After defects were detected and mapped out, the same checksum errors are again detected
by the system health checker.

online

Specifies that a faulty module is kept online, regardless of memory scanning or memory
mapping errors.

«
...
706
707
708
709
710
...
»

Summary of Contents for ExtremeWare 7.5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExtremeWare 7.5

Quality Monitoring

Brand: Nortel Pages: 22

LaserWriter 8.x driver

Brand: Xerox Pages: 12

Brand: Brady Pages: 33

CLOUD DIRECTOR 1.0

Brand: VMware Pages: 3

VmWare ESX Server 2.12 Deployment

Brand: VMware Pages: 34

Brand: VMware Pages: 34

Brand: SonicWALL Pages: 20

POLICY MANAGER PROXY 2.0 -

Brand: F-SECURE Pages: 24

Brand: FieldServer Pages: 8

Brand: Yamaha Pages: 8

Brand: Yamaha Pages: 4

FLASH MX 2004-ACTIONSCRIPT LANGUAGE

Brand: MACROMEDIA Pages: 1104

Digital Vintage Reverb DVR2

Brand: TC Electronic Pages: 16

Brand: Barracuda Networks Pages: 71

Brand: Garmin Pages: 4

PowerShot SX10 IS

Brand: Canon Pages: 464

Brand: HP Pages: 12

StorageWorks 64 - SAN Director Switch

Brand: HP Pages: 160

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands