manualshive.com logo in svg

Extreme Networks ExtremeWare 7.5, Command Reference Manual

Download the free Command Reference Manual for Extreme Networks ExtremeWare 7.5, an advanced networking solution. This comprehensive manual provides detailed instructions and information on utilizing the product's functionalities. Enhance your networking experience by accessing the manual from 88.208.23.73:8080.

Share
Download
background image

 

924

ExtremeWare 7.5 Command Reference Guide

Security Commands

configure vlan dhcp-address-range

configure vlan <vlan-name> dhcp-address-range <start-addr> - <end-addr> 

{<mask>}

Description

Configures a set of DHCP addresses for a VLAN.

Syntax Description

Default

N/A

Usage Guidelines

This command configures in the switch a set of DHCP addresses for a particular VLAN. The configured 
address range can be for a local subnet (the range falls in one of the local subnets of the switch) or a 
remote subnet (the configured IP address does not fall in any of the local subnets of the switch).

To configure address ranges for a remote subnet the optional parameter 

mask

 must be included.

To configure address ranges for a local subnet the parameter 

mask

 should not be used.

You can configure a maximum of 64 local and remote address ranges.

Example

You can allocate IP addresses for a remote subnet (non-local subnet) using the DHCP server. The 
following command configures DHCP address ranges for a remote subnet using the subnet 60.0.0.x/24 
in the VLAN named test:

configure vlan test dhcp-address-range 60.0.0.5 - 60.0.0.40 mask 255.255.255.0

NOTE

The mask option is required when configuring the DHCP address range for the remote subnet.

History

This command was first made available in ExtremeWare 6.2.

This command was added to the Summit “

e

” series of switches in ExtremeWare 7.2e.

This command was modified in ExtremeWare 7.3.0 and ExtremeWare 7.3e to allow remote subnets to be 
configured in ExtremeWare.

vlan-name

Specifies the name of the VLAN to be configured.

start-addr

Specifies the starting IP address in the configured range.

end-addr

Specifies the ending IP address in the configured range.

mask

Specifies the network mask of the range if the range specifies a remote subnet.

Summary of Contents for ExtremeWare 7.5



















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ExtremeWare 7.5

Baracoda KEmul RS232 User Manual preview
KEmul RS232
Brand: Baracoda Pages: 9
RTS RTS ISDN 2002 Operator'S Manual preview
RTS ISDN 2002
Brand: RTS Pages: 51
VegaStream Vega Gateway Engineer'S Manual preview
Vega Gateway
Brand: VegaStream Pages: 33
Cisco 2950C-24 - Catalyst Switch - Stackable Datasheet preview
2950C-24 - Catalyst Switch - Stackable
Brand: Cisco Pages: 18
Cisco CONFERENCING EXTENSIONS - ADMINISTRATOR GUIDE FOR MICROSOFT EXCHANGE Administrator'S Manual preview
CONFERENCING EXTENSIONS - ADMINISTRATOR GUIDE FOR MICROSOFT EXCHANGE
Brand: Cisco Pages: 61
Cisco Cisco mds 9124 - fabric switch Datasheet preview
Cisco mds 9124 - fabric switch
Brand: Cisco Pages: 9
Cisco CISCO1811 End User Instructions preview
CISCO1811
Brand: Cisco Pages: 16
Cisco Cisco MDS 9020 - Fabric Switch Configuration Manual preview
Cisco MDS 9020 - Fabric Switch
Brand: Cisco Pages: 22
Cisco Catalyst X6816 Datasheet preview
Catalyst X6816
Brand: Cisco Pages: 13
Cisco Cisco mds 9124 - fabric switch Specifications preview
Cisco mds 9124 - fabric switch
Brand: Cisco Pages: 3
Cisco DCNM Configuration preview
DCNM
Brand: Cisco Pages: 7
Cisco GEM318P User Manual preview
GEM318P
Brand: Cisco Pages: 74
Cisco Craft Works Interface Quick Start Manual preview
Craft Works Interface
Brand: Cisco Pages: 32
Cisco Catalyst Series Switch 2940 Hardware Installation Manual preview
Catalyst Series Switch 2940
Brand: Cisco Pages: 82
Cisco Catalyst Series Switch 2940 Regulatory Compliance And Safety Information Manual preview
Catalyst Series Switch 2940
Brand: Cisco Pages: 28
Cisco 11.0 BT Release Notes preview
11.0 BT
Brand: Cisco Pages: 58
Cisco CCNA NETWORK SIMULATOR Manual preview
CCNA NETWORK SIMULATOR
Brand: Cisco Pages: 88
Cisco CSACSE-1111-K9 - Secure Access Control Server Solution Engine Installation Manual preview
CSACSE-1111-K9 - Secure Access Control Server Solution Engine
Brand: Cisco Pages: 130

Brands by name

Popular brands

Load more brands