1478
ExtremeWare 7.7 Command Reference Guide
EAPS Commands
State:
On a transit node, the command displays one of the following states:
•
Idle—The EAPS domain has been enabled, but the configuration is not
complete.
•
Links-Up—This EAPS domain is running, and both its ports are up and in
the FORWARDING state.
•
Links-Down—This EAPS domain is running, but one or both of its ports are
down.
•
Preforwarding—This EAPS domain is running, and both of its ports are up,
but one of them is in a temporary BLOCKED state.
On a master node, the command displays one of the following states:
•
Idle—The EAPS domain has been enabled, but the configuration is not
complete.
•
Init—The EAPS domain has started but has not yet determined the status of
the ring. The secondary port is in a BLOCKED state.
•
Complete—The ring is in the COMPLETE state for this EAPS domain.
•
Failed—There is a break in the ring for this EAPS domain.
•
[Failtimer Expired]—When the failtimer expires and it’s action is set to
send-alert, this flag is set. This flag indicates there is a misconfiguration or
hardware problem in the EAPS ring. The EAPS master node will continue to
remain in COMPLETE or INIT state with it’s secondary port blocking.
[Running: …]
•
Yes—This EAPS domain is running.
•
No—This EAPS domain is not running.
Enabled:
Indicates whether EAPS is enabled on this domain.
•
Y—EAPS is enabled on this domain.
•
N—EAPS is not enabled.
Mode:
The configured EAPS mode for this switch: transit (T) or master (M).
Primary/Secondary port:
The port numbers assigned as the EAPS primary and secondary ports. On the
master node, the port distinction indicates which port is blocked to avoid a
loop.
Port status:
•
Unknown—This EAPS domain is not running, so the port status has not yet
been determined.
•
Up—The port is up and is forwarding data.
•
Down—The port is down.
•
Blocked—The port is up, but data is blocked from being forwarded.
Tag status:
Tagged status of the control VLAN:
•
Tagged—The control VLAN has this port assigned to it, and the port is
tagged in the VLAN.
•
Untagged—The control VLAN has this port assigned to it, but the port is
untagged in the control VLAN.
•
Undetermined—Either a VLAN has not been added as the control VLAN to
this EAPS domain or this port has not been added to the control VLAN.
Hello Timer interval:
The configured value of the timer in seconds, specifying the time that the
master node waits between transmissions of health check packets.
Fail Timer interval:
The configured value of the timer in seconds, specifying the time that the
master node waits before the failtimer expires.
Summary of Contents for ExtremeWare 7.7
