1760
ExtremeWare 7.7 Command Reference Guide
IP Unicast Commands
show iproute
For
“i”
series of switches:
show iproute {priority | vlan <vlan name> | permanent | <ip address>
<netmask> | route-map |origin [direct | static | blackhole | rip | bootp |
icmp | ospf-intra | ospf-inter | ospf-as-external | ospf-extern1 |
ospf-extern2]} {mpls} {sorted}
For
“e”
series of switches:
show iproute {priority | vlan <vlan name> | permanent | <ip address>
<netmask> | origin [direct | static | blackhole | rip | bootp | icmp |
ospf-intra | ospf-inter | ospf-as-external | ospf-extern1 | ospf-extern2]}
{sorted}
Description
Displays the contents of the IP routing table or the route origin priority.
Syntax Description
Default
N/A
Usage Guidelines
Route maps for IP routing can be configured based on the route origin. When routes are added to the IP
routing table from various sources, the route map configured for the origin of the route is applied to the
route. After matching on specified characteristics, the characteristics for the route can be modified using
the route maps. The characteristics that can be matched and modified are dependent on the origin of
the route. Route maps for IP routing can be dynamically changed. In the case of direct and static route
origins, the changes are reflected immediately. In the case of routes that are sourced from other origin,
the changes are reflected within 30 seconds.
The output of the
show iproute
command has been enhanced to include information about MPLS
LSPs associated with the routes. The flags field displayed by this command has been enhanced to
priority
Specifies a route priority.
vlan name
Specifies a VLAN name.
permanent
Specifies permanent routing.
ip address
Specifies an IP address.
netmask
Specifies a subnet mask.
route-map
Specifies display of route maps for direct, static, blackhole, RIP, BOOTP, ICMP, OSPF-intra,
OSPF-inter, OSPF as External, OSPF External 1, and OSPF External 2 routing.
NOTE: This option is only available on the “i” series of switches.
origin
Specifies a display of the route map origin.
mpls
Specifies to display MPLS information.
NOTE: This option is only available on the “i” series of switches.
sorted
Specifies to sort the information displayed.
Summary of Contents for ExtremeWare 7.7
