vplsping
ExtremeWare 7.7 Command Reference Guide
2597
vplsping
vplsping {continuous} <vpls_name> [<ipaddress> | mac-address <macaddress>]
{next-hop [<ipaddress> | <host_name>]} {from <source_macaddress>}
{ping-address <ipaddress>} {start-size <size> {end-size <size}} {reply-mode
[ip | mpls | vpls]}
Description
Sends VPLS ping packets to another VPLS node or to a specific destination MAC address.
Syntax Description
Default
N/A
Usage Guidelines
This command sends a VPLS ping packet to another VPLS node. The
vplsping
command can be used
to verify data plane connectivity between any two VPLS nodes. This is useful, since not all failures can
be detected using the MPLS or VPLS control plane. The VPLS ping is a modified MPLS ping sent
in-band over a VC-LSP for a specific MAC address. The target MAC address of the VPLS echo request
may represent a VPLS node's MAC address or a customer MAC address. VPLS nodes forward the VPLS
echo request using their local MAC FDB. If the VPLS ping reaches a VPLS egress node, a VPLS echo
reply is sent based on a local FDB lookup. VPLS ping packets are never forwarded out local VPLS
egress interfaces. The TTL value in the VPLS echo request is set to 255.
The VPLS node can be specified using the ipaddress parameter. When the
ipaddress
parameter is
specified, the IP address is used to look up the corresponding VPLS node's MAC address. If the MAC
address has not been learned, the vplsping command will fail with a “No MAC address learned for IP
address” error. The
mac-address
keyword specifies the MAC address that is being pinged. The
mac-address
may represent the MAC address of a VPLS node or a customer MAC address. The
macaddress
parameter must be a unicast MAC address and is specified as a colon separated list of six
bytes in hex format. The specified or learned MAC address is copied into the destination MAC address
field of the VPLS echo request and is included in the L2-VPN Prefix Target FEC TLV. By default, the
switch's MAC address is used for the source MAC address of the VPLS echo request. The
from
keyword
vpls_name
Identifies the VPLS within the switch (character string)
ipaddress
Specifies the address to look up the corresponding VPLS node's MAC address.
macaddress
Specifies the MAC address that is being “pinged.”
source-macaddress
Specifies the source MAC address used for the VPLS echo request.
start_size
Specifies the number of bytes to include as payload data in the VPLS ping packet.
end_size
Determines if the size of the packet will increment by one byte for each new VPLS echo
request sent.
ip
Determines whether the VPLS echo reply is routed back to the sender, specified in the L2
VPN Prefix sub-TLV, via an IPv4 packet with the IP Router Alert option.
mpls
Determines if the VPLS echo reply is routed back to the sender over an MPLS LSP.
vpls
Determines if the VPLS echo reply is switched in-band back to the sender via a VPLS
encapsulated IPv4 packet.
Summary of Contents for ExtremeWare 7.7
