background image

3 -

 

List of certificated antennas 

Type 

Model 

Connector  5150~5250MHz  5250~5350MHz 5470~5725MHz  5725~5850MHz 

PIFA 

NA 

U.FL

 

PIFA

 

ANT-PIFA7262AG

 

U.FL

 

5.5 

5.5 

5.5 

5.5 

Dipole

 

WS-ANT-5DIP-3 

 

RPSMA

 

Panel

 

WS-AI-DX07025

 

RPSMA

 

5.5 

5.5 

5.5 

5.5 

Panel

 

WS-AI-DX10055 

 

RPSMA

 

6

 

6

 

6

 

6

 

Omni

 

WS-AI-DX02360

 

RPSMA

 

2

 

2

 

2

 

2

 

Sector

 

WS-AI-DT05120

 

RPSMA

 

5

 

5

 

5

 

5

 

Note: The EUT has three antennas. (3TX/3RX) 

 

Any changes or modifications not expressly approved by the manufacturer could void the user's 

authority to operate this equipment. 

 

USERS MANUAL OF THE END PRODUCT: 

In the users manual of the end product, the end user has to be informed to keep at least 20cm separation 

with the antenna while this end product is installed and operated. The end user has to be informed that 

the IC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end 

user has to also be informed that any changes or modifications not expressly approved by the 

manufacturer could void the user's authority to operate this equipment. IC statement is required to be 

available in the users manual: This Class B digital apparatus complies with Canadian ICES-003. 

Operation is subject to the following two conditions: (1) this device may not cause harmful interference 

and (2) this device must accept any interference received, including interference that may cause 

undesired operation.   

 

 

 

 

 

 

 

 

 

 

Summary of Contents for QXO-AP3825E














Reviews: