background image

8 -

 

Industry Canada statement 

This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the 

following two conditions:   

(1) this device may not cause interference, and   

(2) this device must accept any interference, including interference that may cause undesired operation 

of the device. 

 

Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts 

de licence. L'exploitation est autorisée aux deux conditions suivantes :   

(1) l'appareil ne doit pas produire de brouillage, et   

(2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est 

susceptible d'en compromettre le fonctionnement.

 

Caution: 

(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for 

harmful interference to co-channel mobile satellite systems; 

(ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz 

shall comply with the e.i.r.p. limit; and 

(iii) the maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the 

e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate. 

(iv) Users should also be advised that high-power radars are allocated as primary users (i.e. priority 

users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause 

interference and/or damage to LE-LAN devices. 

Summary of Contents for QXO-AP3825E














Reviews: