DTP2 T 204 • Setup Guide
The Extron DTP2 T 204 is an HDCP-compliant, four
input HDMI switcher with a DTP2 output that switches
and extends digital embedded audio, bidirectional
RS-232, IR, and remote power.
It supports video resolutions up to 4K @ 60 Hz and
1080p @ 120 Hz, using shielded twisted pair cabling as
a transmission medium, and extends HDMI video signals
up to 330 feet (100 meters).
The switcher features four HDMI inputs and a
DTP2/HDBT output, data rates up to 18 Gbps, HDR,
12 bit Deep Color, 3D, Lip Sync, HD lossless audio
formats, and SIS to CEC control. EDID Minder®
maintains EDID communication with connected devices
and ensures that the HDMI sources power up properly
and maintain correct video output.
Control is available via front panel buttons, USB, Extron
Product Control Software (PCS), Ethernet, RS-232,
contact closure, and auto-input switching for integration
with any control system. Front panel LED indicators provide immediate visual confirmation of HDCP authentication and signal
presence for each input and output. Remote power for the end unit is available via the DTP output.
This guide provides instructions for an experienced installer to set up and operate this switcher. For full installation,
configuration, and operation details, see the
DTP T 204 User Guide
Rear Panel Features and Connections
INPUTS
OVER TP
DTP2 T 204
1
2
3
4
LAN
RS-232
IR
Tx Rx G Tx Rx
LINK
SIG
OUT
Tx
T
T C
C
T +V
T C
T
G
+V
C
T
G
+V
C
C
1
2
3
4
5
6
Rx
RS-232
G
2.2 A
MAX
POWER
12V
REMOTE
CONT
HDBT
DTP
SEND POWER
OFF
A
B
C D E
F
G H
F
I
Figure 1.
DTP2 T 204 Rear Panel
Installation Steps
1.
Turn off and disconnect all of the equipment
from the power source.
2.
Mount the switcher
on a rack shelf or furniture (optional).
3.
Connect HDMI input sources
to one or more of the DTP2 T 204 inputs (see figure 1,
B
). The default (Extron) EDID is
present at each input and Hot Plug Detect (HPD) is actively controlled on each input.
NOTES:
•
The default (Extron) EDID is 1080p @ 60 Hz (see the
DTP2 T 204 User Guide
for the
EDID table).
•
LockIt
®
cable lacing brackets are provided to secure the HDMI cables to the rear panel
connectors to reduce stress on the HDMI connectors and prevent signal loss due to
loose cable connections (see the
4.
Connect the input of a DTP2 or HDBaseT compatible device
to the DTP/HDBT OUT
RJ-45 connector (
C
). See the image at right to wire the connector.
INPUTS
OVER TP
DTP2 T 204
1
2
3
4
LAN
RS-232
IR
Tx Rx G Tx Rx
LINK
SIG
OUT
Tx
T
T C
C
T +V
T C
T
G
+V
C
T
G
+V
C
C
1
2
3
4
5
6
Rx
RS-232
G
2.0 A MAX
POWER
12V
REMOTE
CONT
HDBT
DTP
SEND POWER
OFF
L
RS-232
IR
Tx Rx
Tx Rx
G
R
POWER
12V
--A MAX
AUDIO
OUTPUTS
OVER DTP2
SIG LINK
DTP2 IN
POWER
12V
0.3A MAX
IPL PRO S3
G
Tx Rx
RTS CTS
G
Tx Rx
RTS CTS
G
Tx Rx
RTS CTS
COM 1
COM 2
COM 3
LAN / PoE
SHARE
SHARE
SHARE
MODEL 80
FLAT PANEL
LAN
LAN
ON
OFF
MUTE
HDMI
Ethernet
Extron
DTP2 T 204
Transmitter
Extron
IPL Pro S3
IP Link Pro
Control Processor
Extron
DTP2 R 211
Receiver
Ethernet
CATx Cable
up to 330' (100 m)
Flat Panel Display
HDMI
RS-232
Extron
CCR 30
Contact Closure Remote
with Three LED Switches
ON/OFF/MUTE Control
Extron
HDMI SM
Show Me Cables
1
Wire color
White-green
Green
White-orange
White-blue
Orange
White-brown
Brown
Blue
TIA/EIA T
568 B
TP Wires
12345678
Pins:
5
Pin
1
2
3
6
7
8
4
A
Power input connector
B
HDMI input connectors
C
DTP/HDBT Output RJ-45 port
D
TP mode switch
E
Over TP RS-232 and IR port
F
Contact input and
tally output
ports with +V connectors
G
Remote RS-232 port
H
LAN RJ-45 port
I
Remote power toggle switch
1
IMPO
RTAN
T:
IMPO
RTAN
T:
Go to ww
w.extr
on.com
for the complete
user guide
, installation instructions,
and
specifications bef
ore connecting the
product to the po
wer sour
ce.
