background image

Operation

Front Panel

DMP 44 LC

DIGITAL MATRIX PROCESSOR

CONFIG

Extron

A

A

Figure 5. 

IR 102 Front Panel

The IR 102 front panel contains the following:

A

 

Power LED

 — When lit, this green LED indicates power is applied. The LED blinks 

during communication activity.

Selecting an Input

 

To select an input on a switcher or the SMD 202 decoder 
using the remote control:

1. 

Aim the handheld unit at the IR Sensor or the front  
panel IR signal detector of the switcher or decoder.

2. 

Press 

two

 numbered buttons for the desired input  

(see figure 6, 

1

, at right) as follows: 

• 

For switcher inputs 1 through 9, press 

0

, followed  

by the input number. For example, for input 1  
press 

01

• 

For switchers with 10 or more inputs, press the  

+10

 button (

2

) to add 10 to the input number  

that you want to select. For example, to select 
input 17, press the 

+10

 button, then the 

7

 button. 

For input 10, press 

+10

, then 

0

The maximum operating range of the IR 102 remote control 
is 30 feet (9.1 meters).

Figure 6. 

IR 102 Transmitter  

Input Selection Buttons

Universal Remote

INPUT/OUTPUT SELECTION

1

2

3

4

5

6

7

8

9

0

+10

IR 102

1

1

2

2

IR 102 User Guide • Installation and Operation

5

Summary of Contents for IR 102

















Reviews: