background image

FCC Class A Notice

This equipment has been tested and found to comply with the limits for a Class A digital 
device, pursuant to part 15 of the FCC rules. The Class A limits provide reasonable 
protection against harmful interference when the equipment is operated in a commercial 
environment. This equipment generates, uses, and can radiate radio frequency energy 
and, if not installed and used in accordance with the instruction manual, may cause 
harmful interference to radio communications. Operation of this equipment in a 
residential area is likely to cause interference. This interference must be corrected at the 
expense of the user.

NOTE:

  For more information on safety guidelines, regulatory compliances, EMI/EMF 

compatibility, accessibility, and related topics, see the 

Extron Safety and 

Regulatory Compliance Guide

 on the Extron website.

Battery Notice

This product contains a user-replaceable battery. 

CAUTION:

  Risk of explosion. Do not replace the battery with an incorrect type. 

Dispose of used batteries according to the instructions.

ATTENTION :

  Risque d’explosion. Ne pas remplacer la pile par le mauvais type de 

pile. Débarrassez-vous des piles usagées selon le mode d’emploi.

VCCI-A Notice

この装置は、クラスA情報技術装置です。 この装置を家庭環境で使用すると、電波妨害を引き

起こすことがあります。 その場合には使用者が適切な対策を講ずるよう要求されることがあります。   
 

VCCI-A

Summary of Contents for IR 102

















Reviews: